allis chalmers ball mill

allis chalmers ball mill -		 minelistings.com

allis chalmers ball mill - minelistings.com

Ball mill, 13' diameter x 21' long, Manufactured by Allis Chalmers (Svedala), rubber-lined mill, with Siemens-Allis 2,000 HP, 4000 volt, 200 RPM synchronous motor, Eaton airflex clutch. Includes trommel discharge, ball mill rejects conveyor, lube system, etc. Offered complete with controls. New in 1979. Completely rebuilt in 1998, Serial number C-2485. Previously used at phosphate minerals processing facility. Also available pumps, spare parts, drives, controls to comprise of complete mill system.

standard bond ball mill grindability test method-procedure

standard bond ball mill grindability test method-procedure

The standard feed is prepared by stage crushing to all passing a 6 mesh sieve, but finer feed can be used when necessary. It is screen analyzed and packed by shaking in a 1000-cc graduated cylinder, and the weight of 700 cc is placed in the mill and ground dry at 250 per cent circulating load.

The grinding charge consists of 285 iron balls weighing 20, 125 grams. It consists of about 43-1. 45- in. balls, 67-1. 17 in. balls, 71-0. 75-in. balls and 90-0. 61 in. balls with a calculated surface area of 842sq. in.

Tests are made at all sieve sizes below 28 mesh. After the first grinding period of 100 revolutions, the mill is dumped, the ball charge is screened out, and the 700 cc of material is screened on sieves of the mesh size tested, with coarser protecting sieves if necessary. The under size is weighed, and fresh unsegregated feed is added to the oversize to bring its weight back to that of the original charge. Then it is returned on to the balls in the mill and ground for the number of revolutions calculated to produce a 250 per cent circulating load, dumped and rescreened. The number of revolutions required is calculated from the results of the previous period to produce sieve undersize equal to 1/3.5 of the total charge in the mill.

The grinding period cycles are continued until the net grams of sieve undersize produced per mill revolution reaches equilibrium and reverses its direction of increase or decrease. Then the undersize product and circulating load are screen analyzed, and the average of the last three net grams per revolution (Gbp) is the ball mill grindability.

When F is the size in microns which 30 per cent of the new ball mill feed passes, P is the microns which 80 per cent of the last cycle sieve undersize product passes, and P1 is the opening in microns of the sieve size tested, then ball mill work index Wi is calculated from the following revised (1960) equation:

The average value of P at 100 mesh is 114 microns, at 150 mesh it is 76 microns, at 200 mesh it is 50, and at 325 mesh it is 26.7. These values of P are to be used in this equation when P cannot be found from size distribution analyses.

The accompanying procedure and table can be used to shorten the calculations required with the new formula. The values of 44.5/(P1)0.23 are listed for each mesh size, and the values of (Gbp)0.82 can be found by interpolation from the table. The average P values are listed in the last column and should be used for tests whenever the actual P value is not available from screen analyses.

used ball mills for sale. allis-chalmers and cyclone | machinio

used ball mills for sale. allis-chalmers and cyclone | machinio

26 x 14 ft (7.9 x 4.2 m) SAG Mill 6,300 HP (4700 kW) Motor Variable speed drive available at extra cost. Mill includes: - main drive motor Slip Ring 6,300 HP - liquid resistance starter, includes variable speed d...

8 units available SPARE PARTS (Additional Cost): - 4 each - Inlet Head Liners - 4 each - Liner Top Cover Plate - 4 each - Vortex - 4 each - Cylinder Liner - 4 each - Skirt - Urethane - 4 each - Apex Insert - 4 ea...

- 1250 HP - 200 RPM - Power factor: 0.8 - Type TS - 4000 Volt - 1250 Kva - 180 Armature amps - 85 Field amps - 125 Excitation volts - 3 Ph/60 Hz - 6524L frame - Continuous duty - Made by General Electric in USA S...

- New unused ball mill made in North America - 1.5 x 3 meter internal shell dimension, less liners - Single piece rolled steel shell - Tire Driven - Rubber liner package with installation hardware - Rubber lined ...

- Two piece shell - Run for only 1.5-2 years - Currently installed - Lubrication system - 3,000 HP induction motor - Clutch - 284 tooth bull gear, with 28 in face - 18 tooth pinion with 28.5 in face - Babbitt bea...

- Shell dimensions: 6 ft 10 in x 10 ft 4 in - Single piece shell - Double scoop feeder - Cast steel heads - Supports for installation of grate discharge - Single piece helical bull gear - 3-piece gear guard - Pin...

- Unused surplus grinding mill - 1,000 liter (265 gallon) - High intensity energy efficient grinding machine - Horizontal configuration, small footprint - Simple installation and maintenance - Ceramic grinding me...

- Marcy ball mill made in USA - Two 7 ft diameter cast heads - Two bearing assemblies with sole plates and babbitt inserts - 15-tooth Pinion assembly with sole plates - Helical bull gear with 12 inch face and 284...

- Welded steel shell - Feed and discharge heads are cast steel - Gearbox, 5.318 ratio - Induction motor: 575V, 1780 RPM, 400 HP - High-speed coupling - Some drawings available - Rubber liners with 60-70% life rem...

6 x 17 ft Allis Chalmers dry grind ball mill with end peripheral discharge - Mill shell with attached feed and discharge ends - Alloy steel liners (installed) - Trunnion bearings, oil lubricated - Spur-type ring ...

- Fluidized vertical mill for very fine and ultra-fine grinding - Designed for small footprint and simple foundation - Modular design for faster installation - Fabricated A-36 steel octagonal mill body with easy ...

Related Equipments