chute feeder weight

the chute feeder - transportation - mingxin

the chute feeder - transportation - mingxin

The chute baseboard makes reciprocating motion, with jig frequency of 20-60/min, stroke of 20-200mm. The stroke can be adjusted by actuating device eccentric gear, eccentric distance is half of stroke. Based on experience of some beneficiation plant production, the eccentric distance should not less than 30mm for viscidity ore. The chute width is approx 2-2.5 times of max feed granularity. The largest chute feeder can satisfied to feed for iron ore granularity less than 500mm. The most common specification is 980*1240 chute feeder, which granularity is 350-0mm, suitable for as feeder of 400*600 jaw crusher.

The chute feeder is used to beneficiation, coal, chemical engineering and other industries, put the granular and blocky material from storage bin into those different input device, but not suitable for conveying concentrate fines and other powdery material.

chute feeder

chute feeder

Chute feeder is a kind of feeding machine whose chute base board moves back and forth. It can be lifted at the discharging mouth of the ore storage bin or installed on the ground and it is mainly used as the feeding equipment for jaw crusher which needs even feeding.

Metallic and non-metallic ores (gold, silver, copper, tantalum, barite, tungsten, quartz, coal, limestone etc.), aggregate (rocks, river stone, blast rock, lava rock), construction waste (asphalt, concrete, bricks, pavers, etc.), and some other materials.

It is suitable to be used in ore beneficiation, coal, chemistry and other industrial departments and it is able to take out the granulate massive materials from the storage bin and send them to different types of material receiving devices, but it is not suitable for feeding concentrate powders or other powdery materials.

Chute feeder is usually installed underneath the discharging opening of ore bin. Minerals fall on the bushing. The bushing is located at the chute bottom, configured on idler wheel and via eccentric device connected with reducer which is linked to electric motor by coupler. When it works, electric motor drives reducer via coupler; eccentric disk and drain cap which is situated between chute frame bottom and roller begin to do reciprocal and linear motion so as to uniformly feed minerals.

chute feeder, manufacturer of chute feeder - xinhai

chute feeder, manufacturer of chute feeder - xinhai

The machine is usually installed underneath the discharging opening of the ore bin. Minerals fall on the bushing. The bushing is located at the chute bottom, configured on the idler wheel, and via an eccentric device connected with a reducer which is linked to an electric motor by a coupler. When it works, the electric motor drives a reducer via a coupler; eccentric disk and drain cap which is situated between the chute frame bottom and roller begins to do reciprocal and linear motion to uniformly feed minerals.

china chute feeder, chute feeder manufacturers, suppliers, price

china chute feeder, chute feeder manufacturers, suppliers, price

China manufacturing industries are full of strong and consistent exporters. We are here to bring together China factories that supply manufacturing systems and machinery that are used by processing industries including but not limited to: feeding machine, vibrating feeder, feed machine. Here we are going to show you some of the process equipments for sale that featured by our reliable suppliers and manufacturers, such as Chute Feeder. We will do everything we can just to keep every buyer updated with this highly competitive industry & factory and its latest trends. Whether you are for group or individual sourcing, we will provide you with the latest technology and the comprehensive data of Chinese suppliers like Chute Feeder factory list to enhance your sourcing performance in the business line of manufacturing & processing machinery.

feeder machine types | how to choose a feeder equipment | m&c

feeder machine types | how to choose a feeder equipment | m&c

Feeder machine is a kind of feeding equipment which can feed bulk and granular materials from the stock bin to the receiving devices evenly, regularly and continuously. Which has been widely used in cement, mining, metallurgy, coal, chemical industry, ceramics, grain, electric power and other industrial and mining enterprises.

Feeder machine is the most ideal equipment to realize production automation. The feeder machines can not only be used with electronic scales or microcomputers, but also can work alone for feeding. The common types of feeder machine are as follows:

When vibrating feeder is working, the vibrating motor drives the eccentric shaft or eccentric block to drive, and the centrifugal force produced by the rotation of the eccentric block is used to make the screen box and vibrator move in a continuous circle or approximate circle, and the bulk and granular materials from stock bin are fed into the receiving device uniformly, regularly and continuously .

Vibrating feeder is widely used in crushing and screening equipment of coal mine, mineral processing, chemical industry and mills etc. Usually suspended under the stock bin by a spring, the feeder trough can be arranged horizontally or with an angle of no more than 10.

Belt feeder is the same as that of belt conveyor in structure, but the roller space of belt feeder is smaller to bear the pressure of materials in the silo. Guide baffles are arranged on both sides of the conveyor belt to prevent spreading. The belt speed < 0.5 m/min. The feed rate can be adjusted by changing the belt speed or the height of the outlet baffle.

Belt feeder has the advantages of large bearing capacity and short length, so it is also a kind of economical feeding equipment. The feed ore size suitable for belt feeder is less than 350mm and the belt speed is below 0.3m/s generally. Belt feeder is mainly used in ore buffer bin discharge after coarse crushing, ore feeding of medium/fine crushers or screening equipment, discharge of powder bin.

Plate feeder is suitable for short distance transportation and can bear heavy working load, including 3 types: heavy, medium and light. The maximum ore size of heavy plate feeder can reach more than 1000mm. The plate feeder is mainly used for coarse crushing ore feeding, ore buffer bin drainage after coarse crushing, and coarse ore heap discharge.

Plate feeder can be installed horizontally or tilted, with a maximum upward inclination of 20. It is suitable for materials with loose density less than 1200kg/m, block weight less than 140kg and temperature below 350.

Chute feeder is suitable for the ore feeding of medium-sized materials, the maximum particle size can reach 450mm, and the ore feed can be adjusted by adjusting the eccentricity of the eccentric wheel of the transmission mechanism. The width of the trough body of the chute feeder is 2-2.5 times of the maximum particle size of the ore feed, which is mainly used for the feeding of jaw crusher and bulk lime in the preparation of lime milk.

Pendulum feeder is suitable for short distance transportation and high specific gravity materials with a particle size of 35 100mm. Pendulum feeder is not suitable for conveying dry powder materials, otherwise dust pollution and outlet blockage will occur.

Pendulum feeder is mainly used as the feeding equipment of the belt conveyor when collecting ore in the ball mill, and the feed particle size is generally less than 25mm, which belongs to intermittent feeding.

Disk feeder is a kind of continuous volume feeding equipment composed of driving device, feeder body, metering belt conveyor and metering device, which makes use of the fluidity of materials. The material is scraped from the container to the receiving equipment through a rotating disc and an adjustable scraper, which is suitable for all kinds of non-viscous and not very good fluidity -20mm fine materials.

Screw feeder can be installed in the lower part of the silo and is suitable for horizontal, vertical or inclined conveying. The material flow is controlled and adjusted uniformly and continuously by changing the spiral speed. The screw feeder is easy to feed non-viscous powdery, granular and small particle materials evenly to the receiving equipment from the silo and other storage equipment.

Screw feeder has the features of conveying, sealing, homogenizing and stirring. It is a common equipment in cement raw meal homogenization and silo sealing feeding. There are many types of screw feeder, such as solid screw, belt screw, variable pitch screw, conical screw and so on.

Impeller feeder is composed of a group of blades installed on the shaft and the outer sealing shell. Driven by the motor, the impeller on the spindle is driven by the reducer to drive the material from the upper silo through the impeller groove to feed out evenly. The feeding capacity is changed by adjusting the speed of the impeller.

Scraper feeder is composed of many scrapers fixed between two chains with a certain distance between them. The scraper moves along the slot bottom, which can be used for horizontal transportation or inclined transportation. When transporting upward along the incline, the inclination of the material layer shall not exceed 25 , and when transporting downward, the inclination shall not exceed 20 .

The working principle and traction parts are the same as the scraper conveyor. Scraper feeder can realize closed and multi-point feeding, which is suitable for materials with less powder or granule, grindability and stickiness.

Electromagnetic vibratory feeder uses the electromagnetic vibratory exciter as the vibration source to drive the hopper, which has the features of small amplitude, high frequency, slow conveying speed. Electromagnetic vibratory feeder is a new type of quantitative feeding equipment, which can meet the requirements of continuous production.

The maximum ore feeding particle size of electromagnetic vibratory feedercan reach 500mm, it is widely used for ore feeding of medium and fine crushing equipment and screening equipment, ore discharge of ore bin, etc.

Related Equipments