crushers solution solving

common problems and solutions in the impact crusher

common problems and solutions in the impact crusher

Impact crusher is usually used as secondary or fine crusher in stone crushing plant. Within the working process of impact crusher, there might some situations and it's very important to know how to solve these problems. During this article, we'll introduce some common problems and solutions within the impact crusher.

Reasons and Solution: There might be several reasons cause the abnormal vibration of impact crusher. The first one is the raw materials are too big. The operator should check the feed size of raw materials and separate the bulk ones out. The second one is the unevenly worn of the blow bar. To solve this, the operator can replace the blow bar with a new one. The third reason is that the rotor loses balance and needed to be adjusted. The last one is that the base is unstable. The operator should check the foundation bolts and tighten them.

The gap between blow bar and impact plate is too big. The operator should adjust the gap size. Normally the gap size should between 15-20mm. The over-sized raw materials will also affect the final product size, so the raw materials should under the allowed ranges.

Reasons and solutions:The belt wears. To solve this problem, the operator should exchange the V-belt. The installation of the belt is improper. While installation the belt, the belt and the belt pulley should be in the same plane. Pay attention to the quality of the V-belt.

Solution: operators should turn off the power immediately, stop the machine and clean the crushing cavity to see if there is any materials that cannot be crushed enter the crushing cavity. The second might reason is that the impact plate falls down. To solve this problem, operators should stop the machine and fix the impact plate.

In order to solve such problems as low production efficiency and difficult installation and maintenance, ZENITH developed a new generation of jaw crusher--- C6X Series Jaw Crusher. It is the most ideal coarse crushing equipment on current market because a

As the new generation of crusher, PEW Series Jaw Crusher is born with innovative significance. The unique design concept makes this crusher achieve perfect combination between crushing efficiency and operating cost.

cause analysis and problems solving of jaw crusher | hxjq

cause analysis and problems solving of jaw crusher | hxjq

The jaw crusher is mainly composed of a frame, a movable jaw assembly, a movable jaw, a fixed jaw, a triangular wheel, a flywheel, a bracket, a side guard, a discharge port adjusting device and a driving device. Because of its simple structure, easy manufacture, reliable operation and convenient maintenance, it has been widely used in crushing operations in metallurgy, chemical industry and mining industries.

In the jaw crusher, the ore is crushed and reduced to the required particle size. When the moving plate moves away from the fixed plate, the ore is sliding down freely from the upper portion of the crushing chamber to the discharge port under the action of gravity. During this process, the ore slides down along the surface of the jaw plate and causes sliding friction which makes the jaw plate be worn. Therefore, the abrasive wear is an important wear type caused by the squeezed ore.

When the ore is squeezed and ground under the huge mechanical force of the jaw plate, it is easy to form hard sharp edges and corners, and continual interaction between ore and the jaw plate makes the surface of the jaw plate appear very deep scratches, dense grooves and large-area deep pits. As a result, under the strong chiseling action, the jaw plate develops plastic deformation, metal rheology, brittle fracture and spalling, causing the material of jaw plate continuously to migrate and lose, and gradually become thinner. Therefore, chiseling wear is the main form of wear.

Jaw crusher has a large crushing force and fast running speed. Under the action of the huge impact and crushing stress, it withstands long-term and periodic contact fatigue load and is prone to fatigue crack. Therefore, fatigue spalling is also one of the causes of wear.

In order to protect the environment and improve working conditions, a water spray facility is installed on the site of the jaw crusher for dust suppression. At the same time, the water directly contacts the raft which accelerates the oxidation and corrosion of the raft and causes corrosion and wear of the raft.

The wear of the jaw plate presents complexity and diversity and is affected by factors such as materials, abrasives, environmental media, and relative motion. The value of the moving motion is usually reduced to solve the wear problems. In recent years, with the rapid development of computer technology, software simulation is used to comprehensively consider various factors that cause wear, and dynamically imitate of the crushing movement of the jaw plate, so as to more comprehensively analyze the wear rules of the jaw plate and finally reduce its wear rate.

In addition to the wear problem of the jaw plate, there are many other problems caused by parts and components can not be ignored. Next, we will introduce the failure analysis and troubleshooting of the jaw crusher.

4Check the tooth gap size of the tooth plate. If it does not meet the standard, the jaw plate must be replaced, and the relative position of the fixed jaw plate and the movable jaw plate should be adjusted to ensure that the tooth top is fixedly pressed against the tooth root to prevent displacement.

6It is non-bearing temperature rising, but the sealing sleeve of the movable jaw rubs with the end cap, which causes friction heating, or the double embedded cover of the frame bearing seat and the spindle rotate together, causing friction and heat.

6Replace the end cap and the sealing sleeve, or loosen the upper bearing cap of the end of the frame bearing housing which is overheated, press the fuse and the insert cover into the bearing housing groove, and then fix the bearing cover to eliminate the cover rotation.

home | international crusher solutions

home | international crusher solutions

International Crusher Solutions Ltd was established in 1991 and has since earned the respect of the quarrying and cement production industries as one of the leading suppliers of quarry plant and quality crusher wear parts.

We have just supplied a Mansfield No3 Centre Feed & Mansfield No 3 Side Feed both complete with new 110kW motor, pulleys, belts, guards, feed chute and discharge chute to a customer who will be operating them in France.

crushing solutions - h-e parts

crushing solutions - h-e parts

H-E Parts supply world-class CME manganese crusher liners and wear materials. The companys dedicated engineering division is adept at designing manganese liner profiles to meet customers specific product requirements. In addition, H-E Parts offers crusher parts for most brands and makes in the market along with a full range of wear products including wear plate and ceramic liners. H-E Parts can offer minerals processing, plant asset management or the entire scope of maintenance support required by our customers.

H-E Parts International replacement parts are compatible with the makes and/or models of the third-party equipment described. H-E Parts International is not an authorized repair facility of these third parties and it does not have an affiliation with any manufacturers of these third-party products. All brands, original equipment manufacturer (OEM) part numbers or references are owned by the respective OEM entities or their affiliates. These terms are used by H-E Parts International for identification and cross reference purposes only and are not intended to indicate affiliation with, or approval by the OEM, of H-E Parts International or its products.

the common questions of cone crusher and corresponding solutions | hxjq

the common questions of cone crusher and corresponding solutions | hxjq

Crushing machine is the most widely used equipment in the mining industry, and it is divided into several types according to different applications. The cone crusher is one of the most common ones and often used as the secondary crushing machine in the whole stone crushing process.

During the operation of the cone crusher, the operator often encounters a variety of problems. This article will list the common problems of the cone crusher and our professional engineers will give the most appropriate solutions, hoping it can help you.

Poor oil quality will reduce the viscosity of the oil film, causing the oil film to rupture in the process of breaking the spindle bushing, causing the copper sleeve to burn out. Therefore, it should be checked and replaced in time.

When the oil tubing is blocked or the oil pump's capacity is reduced, it is easy to cause the copper bush to be oil-free and the oil film cannot be formed until the copper sleeve is burnt. Therefore, the pipeline and the oil pump should be inspected regularly to ensure sufficient oil.

If the materials are mixed with iron, iron will increase the instantaneous load of the crusher, causing the oil film to rupture and burning the copper bush. Therefore, the metal detector on the feeding machine should maintain a sensitive and reliable state.

The gap between the spindle and its bushing should be kept between 1.0 and 1.2 mm. If it is too large or too small, the copper bushing will be burnt. Therefore, the gap between the spindle bushing and the spindle should be carefully checked during the replacement of new bushings.

The deformation of the spindle will cause a significant reduction in the cooperation between the spindle and the spindle bushing, especially after the crusher is running hot, causing the copper sleeve to burn. Therefore, the spindle status needs to be checked regularly.

Generally, the gap between the locking ring and the adjusting ring of the newly installed crusher is 12.5 mm. Therefore, according to the wear condition of the adjusting ring and the locking ring thread, the gap between the two can be appropriately increased to increase the locking force.

Different types of cone crushers have different maximum feeding sizes. Once the size of materials exceeds the maximum feeding range, the crushing load will increase and the locking force will be relatively insufficient, causing the adjustment ring to vibrate and adversely affect the product size. Therefore, the feed size needs to be strictly controlled.

Due to the improper or unreasonable position of the crusher feeding chamber, the feeding center and the crusher center seriously deviate, resulting in an unbalanced crushing force of the crusher, which makes the adjusting ring has a large force on one side.

The locking ring and the adjusting ring are combined by four bolts. Due to there is mixed with iron in material or the feeding size is overlarge, causing the locking bolt of crusher overload and brake, and the adjusting ring vibrates. Therefore, under this condition, the locking bolts should be replaced and the gap between the locking ring and adjusting ring should be set in the correct position.

The short type cone crusher with the longest parallel band can crush materials to a relatively fine size. And generally, it is used in the fine crushing process; while standard type cone crusher can crush materials to a relatively coarse size, but it has a high output and usually used in the middle crushing process.

During the crushing process, the worn condition of the sealing ring between the shaft frame and the mainframe should be checked. After a long term of use, this part of cone crusher may be worn and the original flexibility of the sealing ring would be reduced.

The reason for the oil leakage may also be that the oil cannot be quickly discharged from the equipment, especially when the oil temperature is low. Therefore, in the production, it should be checked whether there is any dirt in the main oil drain hose or pipe. Otherwise, the accumulation of dirt will hinder the flow of oil, which will cause the cone crusher to leak oil.

If the oil return hole of the U-shape tile of the cone crusher is too small, the lubricating oil will be leaked, and the amount of oil returned is small, which cant satisfy the well-lubrication of gears. In this case, it is necessary to appropriately increase the oil return hole of the U-shape tile to ensure the oil return amount, and fundamentally solve the problem of ole leakage and poor lubrication of the bevel gear.

The lubricating oil enters the lower part of the main shaft from the inlet pipe and is rubbed by the lubricating friction disc. If the working pressure of the cone crusher lubrication system is improper, the oil will be ejected from the shaft gap, causing the lubricating oil to leak downward along the outer circumference of the sealing cylinder.

If the gap between the inner wall of the base oil sump and the counterweight oil baffle ring plate is too small, the lubricating oil between them will easily form an oil seal under the action of tension during the working process of the cone crusher. Under the pressure of the air pressure, the oil seal will continuously overflow from the dust seal along the inner wall of the mainframe.

The design of the sealing structure is related to the effect of the sealing and the life of the sealing ring. The sealing effect of the sealing ring depends on the size of the mounting groove. The sealing ring installation groove is too deep and the compression of the sealing ring is insufficient of which will make a bad sealing effect.

Install the sealing ring correctly to ensure that the equipment is well sealed. Do not install the sealing ring with an angled tool to prevent scratching from the rings and avoid stretching it to deformation. Lubricate the sealing ring properly for installation.

Therefore, we should prohibit the temperature rise of the lubricating oil by increasing the heat dissipation area of the fuel tank to improve the heat dissipation effect of the fuel tank. If necessary, a cooler can be added to reduce the temperature of the lubricating oil.

The author hopes that the above questions and corresponding answers can help you. If you have any other questions about the cone crusher, please fill out the message form on the right or send us an email, our engineers will give you the first reply.

rubik's 3x3 solution guide | rubik's official website

rubik's 3x3 solution guide | rubik's official website

Rubiks Speed features a stronger core and has a mechanism designed to make it faster, smoother and more reliable than ever. The speed Cube comes pre-lubricated to help you get faster times, and more can be added when needed. Enjoy seamless, gliding play every time. Available exclusively on Rubiks.com.

crushers - all crusher types for your reduction needs - metso outotec

crushers - all crusher types for your reduction needs - metso outotec

All rock crushers can be classified as falling into two main groups. Compressive crushers that press the material until it breaks, and impact crushers using the principle of quick impacts to crush the material. Jaw crushers, gyratory crushers, and cone operate according to the compression principle. Impact crushers, in turn, utilize the impact principle.

As the name suggest, jaw crushers reduce rock and other materials between a fixed and a moving jaw. The moving jaw is mounted on a pitman that has a reciprocating motion, and the fixed jaw stays put. When the material runs between the two jaws, the jaws compress larger boulders into smaller pieces.

There are two basic types of jaw crushers: single toggle and double toggle. In the single toggle jaw crusher, an eccentric shaft is on the top of the crusher. Shaft rotation causes, along with the toggle plate, a compressive action.

The chewing movement, which causes compression at both material intake and discharge, gives the single toggle jaw better capacity, compared to a double toggle jaw of similar size. Metsos jaw crushers are all single toggle.

Gyratory crushers have an oscillating shaft. The material is reduced in a crushing cavity, between an external fixed element (bowl liner) and an internal moving element (mantle) mounted on the oscillating shaft assembly.

The fragmentation of the material results from the continuous compression that takes place between the liners around the chamber. An additional crushing effect occurs between the compressed particles, resulting in less wear of the liners.

Cone crushers resemble gyratory crushers from technological standpoint, but unlike gyratory crushers, cone crushers are popular in secondary, tertiary, and quaternary crushing stages. Sometimes, however, the grain size of the processed material is small enough by nature and the traditional primary crushing stage is not needed. In these cases, also cone crushers can carry out the first stage of the crushing process.

Cone crushers have an oscillating shaft, and the material is crushed in a crushing cavity, between an external fixed element (bowl liner) and an internal moving element (mantle) mounted on the oscillating shaft assembly.

An eccentric shaft rotated by a gear and pinion produces the oscillating movement of the main shaft. The eccentricity causes the cone head to oscillate between open side setting and closed side setting discharge opening.

The fragmentation of the material results from the continuous compression that takes place between the liners around the chamber. An additional crushing effect occurs between the compressed particles, resulting in less wear of the liners. This is called interparticular crushing also.

Depending on cone crusher, setting can be adjusted in two ways. The first way is for setting adjustment to be done by rotating the bowl against the threads so that the vertical position of the outer wear part (concave) is changed. One advantage of this adjustment type is that liners wear more evenly.

To optimize operating costs and improve the product shape it is recommended that cone crushers are always be choke fed, meaning that the cavity should be as full of rock material as possible. This can be easily achieved by using a stockpile or a silo to regulate the inevitable fluctuation of feed material flow. Level monitoring devices detect the maximum and minimum levels of the material, starting and stopping the feed of material to the crusher, as needed.

Impact crushers are traditionally classified to two main types: horizontal shaft impact (HSI) crushers and vertical shaft impact (VSI) crushers. These different types of impact crushers share the crushing principle, impact, to reduce the material to smaller sizes, but features, capacities and optimal applications are far from each other.

Horizontal shaft impact (HSI) crushers are used in primary, secondary or tertiary crushing stage. HSI crushers reduce the feed material by highly intensive impacts originating in the quick rotational movement of hammers or bars fixed to the rotor. The particles produced are then further fragmentated inside the crusher as they collide against crusher chamber and each other, producing a finer, better-shaped product.

VSI crusher can be considered a stone pump that operates like a centrifugal pump. The material is fed through the center of the rotor, where it is accelerated to high speed before being discharged through openings in the rotor periphery. The material is crushed as it hits of the outer body at high speed and due to rocks colliding against each other.

Selecting optimal crushing equipment can be difficult. Luckily there are tools and software available that simplify weighting different options and help in making decisions. The backbone of all these analyzes are careful calculations that take into account the capabilities and constraints of different crushers and operational requirements.

Every crushing site and operation is different, and theoptimal results are normally obtained by combining theoretical conclusions with practical experience of different materials, operational conditions, maintenance needs, and economic aspects of various alternatives.

Below are some key issues listed according to crushing stages in brief. While defining the best technical solution for your requirements, its good to remember that many crushers are available not only as stationary but also asmobileorportableversions in case you prefer to move or transport your crusher at the production site or between sites regularly.

If you are interested in more detailed analyzes tailored just for your crushing operations, please contact Metso experts. We have practical experience of thousands of different crushing applications around the world, and we are happy to help in finding the equipment that best fits your needs.

The main purpose of a primary crusher is to reduce the material to a size that allows its transportation on a conveyor belt. In most crushing installations a jaw crusher takes care of primary crushing. Plants with very high capacities that are common in mining and less popular in aggregates production, normally use a primary gyratory crusher. When the processed material is easy to crush and not very abrasive, an impact crusher may be the best choice for primary crushing.

One of the most important characteristics of a primary crusher is its capacity for accepting feed material without bridging. A large primary crusher is, naturally, more expensive than a smaller one. Therefore, the investment cost calculations for primary crushers are compared together against the total costs of primary stages, including quarry face clearing, blasting, and drilling costs. In many cases, dump trucks transport the rock to a stationary primary crusher. This may be an expensive solution. Amortization, fuel, tires, and maintenance costs can be included when the vehicles are in high demand. In modern aggregates operations, the use of mobile primary crushers that can move alongside the rock face is, in many cases, the most economical solution.

In terms of the size of the feed opening, the client gets a better return on investment when the primary crusher is a jaw crusher. That means less drilling and blasting because the crusher accepts larger boulders. The disadvantage of this type of crusher, when high capacity is required, is the relatively small discharge width, limiting the capacity as compared with the discharge circuit of a gyratory crusher. Jaw crushers are mainly used in plants producing up to approximately 1600 t/h.

The primary gyratory crusher offers high capacity thanks to its generously dimensioned circular discharge opening (which provides a much larger area than that of the jaw crusher) and the continuous operation principle (while the reciprocating motion of the jaw crusher produces a batch crushing action). The gyratory crusher has no rival in large plants with capacities starting from 1200 t/h and above. To have a feed opening corresponding to that of a jaw crusher, the primary gyratory crusher must be much taller and heavier. Also, primary gyratories require quite a massive foundation.

The primary impact crusher offers high capacity and is designed to accept large feed sizes. The primary impact crushers are used to process from 200 t/h up to 1900 t/h and feed sizes of up to 1830 mm (71") in the largest model. Primary impact crushers are generally used in nonabrasive applications and where the production of fines is not a problem. Of all primary crushers, the impactor is the crusher that gives the best cubical product.

If the intermediate crushing is done with the purpose of producing railway ballast, the quality of the product is important. In other cases, there normally are no quality requirements, except that the product be suitable for fine crushing.

Due to their design, cone crushers are generally a more expensive investment than impactors are. However, when correctly used, a cone crusher offers lower operating costs than a conventional impact crusher. Therefore, clients crushing hard or abrasive materials are advised to install cone crushers for the final crushing and cubicising stage.

Cone crushers can in most cases also give a good cubic shape to fine grades. They can be adapted to different applications. This is an important factor, as client-specific needs often change during a crushers lifetime.

The conventional type has horizontal shaft configuration, known as HSI. The other type consists of a centrifugal crusher with vertical shaft, generally known as VSI. Impactor operation is based on the principle of rapid transfer of impact energy to the rock material. Impactors produce cubic products, and they can offer high reduction ratios as long as the feed material is not too fine. This means that in certain cases it is possible to use a single impact crusher to carry out a task normally done in several crushing stages using compressing crushers (i.e., jaw, gyratory, and/or cone crushers). Impactors are mostly used for nonabrasive materials.

Conventional horizontal-shaft impact crushers are available in various sizes and models, from high-capacity primary crushers for large limestone quarries to specially designed machines for the crushing of materials such as slag.

There are two main categories of VSI crushers machines with impact wear parts around the body and machines that use a layer of accumulated material. The first type is in many respects similar to the conventional impactor with horizontal shaft and rotor. The second type became quite popular in the past decade and is known as the Barmac crusher. The difference between a conventional impactor and a VSI of the Barmac type is that the latter offers lower operating costs, but its reduction ratio is lower also. In a Barmac VSI, the material undergoes an intense rock-on-rock crushing process. In the other crushers, most of the reduction is done by the impact of stone against metal.

Customers operating old, rebuilt, or expanded plants often have problems with the shape of the product. In these cases, the addition of a Barmac VSI in the final crushing stage offers a solution to product shape problems.

The same applies to many mobile crushing units. As the number of crushing stages is normally small with this type of plant, it is almost impossible to obtain a good product shape unless the rock is relatively soft and thus more suited for the production of cubic product. A centrifugal crusher in the final stage can help to solve the problem.

Get the maximum potential out of your size reduction process to achieve improved crushing performance and lower cost per ton. By using our unique simulation software, our Chamber Optimization experts can design an optimized crushing chamber that matches the exact conditions under which you operate.

7 hammer crusher common problems and solutions

7 hammer crusher common problems and solutions

Hammer crusher is an equipment that uses impact form crushing materials. The crusher machine divides into a single rotor and a double rotor. The single rotor is divided into reversible and irreversible. The hammer crusher is widely used for fine crushing of medium hardness materials because of its high productivity and easy maintenance. The hammer mill crushers play an important role in the whole stone crusher plant. It will inevitably appear a variety of problems during hammer crusher working. The problems need to be resolved in time once find. This article will talk about 7 hammer crusher common problems and solutions.

Reason: improper bearing design selection. The processing accuracy of hammer crusher parts can not meet the requirements. Poor installation quality. Vibration factors. Poor lubrication, bearing wear and failure. V belt tension is too large. Improper maintenance methods. The environment temperature is too high.

Reason: Not crushing materials enter the hammer crusher machine. Lining fastener is loose and hammer strikes the lining. Hammer or other parts are broken. Solution: Stop and clean up the broken cavity. Check the tightness of the lining board and the clearance between the hammer and the screen. Replace the broken parts.

Reasons: replacement of hammerhead or cone headwear makes rotor static balance counter condition. Hammerhead broken. Rotor unbalance. Pin roll bending, broken. Triangular plate or disc cracks. Anchor bolt lose.

Solution: remove the hammerhead and choose hammerhead according to the weight which makes the total weight of hammer on each hammer shaft equal to the total weight of hammer on its relative hammer shaft. That is the static balance to meet the requirements

The so-called bearing locking is the bearing in the operation of a large number of heat. The heat in a short time can not be dissipated which leads to locking. This phenomenon in equipment as well as the production service site is very common. The specific causes of bearing heat have the following aspects.

Misfit of bearing outer ring and housing bore or bearing inner ring with shaft during assembly. Improper control of bearing heating temperature during assembly. Improper adjustment of bearing clearance during assembly. These three improper assemblies will cause the bearing heat, resulting in the bearing holding dead.

Oil Seal is used to seal the rotating shaft of mechanical equipment with oil seal components, and the cavity is basically static. So the oil seal is also known as the rotating shaft lip seal. For the oil seal with auxiliary lip, the auxiliary lip has the function of dust-proof which prevents the impurity invasion. And in order to prolong the life of the oil seal. The auxiliary lip often has bad lubrication, and the friction force is big which causes the oil seal to dry friction and the damage. So the installation of a double lip oil seal must be between the lips filled with grease.

During the assembly process, if the gauge is not carefully checked, the temperature will rise rapidly after a certain period of time. Bearing outer ring size has been determined by the end cover and the mouth of the bearing seat, the size of the diaphragm sleeve reduced. The size of the inner ring will be adjusted by the round nut, and finally compressed. the axial clearance of the bearing reduced, making it hot during operation.

Bearing Grease should not be too much. If fat amount is too large which will increase the friction Torque, bearing temperature rise. But if fat amount is too small that cant obtain reliable lubrication and dry friction. Generally speaking, the proper amount of grease is 1 / 3 ~ 1 / 2 of the total void volume in the bearing. Therefore, according to the use requirements, regular injection of the appropriate amount of grease.

Check whether the screw is loose, whether the lubrication is good, whether the parts damaged ( parts such as center feed pipe, conical cover, impeller, underflow liner, circumferential guards and jaws, etc.). Repair or replace in time if they worn out. At the same time, the weight, type, and size of the replacement part must be changed according to the original part parameters. It is best to check the equipment before use to ensure the normal operation of the equipment. Do those also can extend the life of the machine, reduce maintenance costs.

Jiangxi Shicheng stone crusher manufacturer is a new and high-tech factory specialized in R&D and manufacturing crushing lines, beneficial equipment,sand-making machinery and grinding plants. Read More

solution finding vs problem solving

solution finding vs problem solving

For example your car stops running; it is out of gas that is a problem. You can determine where the nearest gas station is, take the bus, ride your bike, etc You determine it is best to find the gas station, go to the gas station and fill your car. Problem solved.

This is effective with machines because the problem is identifiable and either a part can be replaced, more resources added, or an adjustment can be made to fix the problem. The effectiveness of the machine is increased and the problem is solved.

A different challenge comes when working with human complex adaptive systems like leadership, management, performance, planning, communication of tasks & objectives, and collaboration. These areas the problem is not as easily defined as in a machine.

In a human system the part cannot be removed and repaired, so the decisions become more complex. Complexity increases because human systems are interactive and what you see as the effect is not related to a cause.

For example Jackie, your Production Manager and Anthony your Sales manager continually bicker and are at the point where their mutual antipathy is affecting not just their work, but the work of their subordinates as well. Both Jackie and Anthony are competent hard workers who are proven high performers. In this scenario identifying the cause of the problem may not be as obvious as the caror it may reinforce the negative interactions. Leaving both Jackie and Anthony with no clear solution on how they can change their views and behavior of each other. They both know why they dont get along but nothing has changed they still both feel the same.

Solutions finding is a function of every manager. The job of a manger is to add value to people, and to increase their ability to make decisions and solve problems. Work is seeing that decisions are made and problems are solved; this is what you are paid for.

The Solution Finding Model places responsibility onto the person and manager to find and enhance what is working. Using the steps above releases the consistent focus on what is broken and moves the person to find what is the solution.

Replacing, the Problem Model of how will you know that Jackie and Anthony are getting along? They will no longer be fighting with each other. Which describes the absence of the problem; The absence of the problem is not a solution because by default you need to resurrect the problem to compare it with the absence of the problem, mentally reinforcing the problem that you began with, possibly leading to a return of the problem you started with.

To, the Solutions Model of how will you know that Jackie and Anthony are getting along? I will see in-formal and casual conversations between them at team meetings. When either one of them speaks the other will listen and respond in a respectful tone and manner. I will see improved communications between the Production and Sales staff, both teams working together without necessary prompting from other Managers and me. Now you have solutions and some goals to move towards. As a manager you can begin to coach and create action-plans to achieve the solutions, using the steps of the Solutions Model above.

candy crush level 1055 cheats: how to beat level 1055 help

candy crush level 1055 cheats: how to beat level 1055 help

These Candy Crush Level 1055 cheats will help you beat level 1055 on Candy Crush Saga easily. Candy Crush level 1055 is the fifteenth and last level in Mellow Marshmallow and the 476th jelly level. To beat this level, you must crush 81 double jelly squares in 5 moves or fewer. You have 6 candy colors and 81 available spaces. You can get a maximum of 2,000,000 points.

Strategy: The obvious move, color bomb + color bomb combination, is not a good idea as your first, second or third move. Your first move depends on whether you can make a color bomb + wrapped or color bomb + striped combination straight off. If you can, you should make that move. If not, you should eliminate one color and hope for such a combination to be possible for move two. Your choice between color bomb + wrapped and color bomb + striped (if you have a choice) depends on your aim. color bomb + striped gets you closer to closing out the game but color bomb + wrapped makes it far more likely that you will achieve 2,000,000 points and three stars. However far you have got after three moves, you should try a color bomb + color bomb combination for move four. If you have already eliminated most or all of the double jellies, this will close you out. Otherwise, it might still complete the board or get you very close so you can close out with your final move.

There are only five moves to clear the jelly. However the board starts with several columns of candies, so when the player starts the level, a lot of color bombs or striped candies will be created. This level can be completed in two moves, possibly even one. However, if no striped candies come up at the start, it is going to be harder. The creation of color bombs at the start might help you clear some jelly if you are lucky. The jellies are worth 162,000 points. Hence, an additional 338,000 points is required to earn one star.

home - crushertv

home - crushertv

Im Alan P. Brown, productivity coach and mess-to-success entrepreneur. I created CrusherTV, the video library designed to unleash the power of your unique brain so you can accomplish more in less time with less drama.

The actions that lead to an extraordinary life are small and easy. This quote from my friend and serial entrepreneur Jonathan Butcher is a fact. I will share a handful of micro-hacks you can stack to quickly boost your energy, focus and fortunes. With CrusherTV Member, Brian Jordan.

The actions that lead to an extraordinary life are small and easy. This quote from my friend and serial entrepreneur Jonathan Butcher is a fact. I will share a handful of micro-hacks you can stack to quickly boost your energy, focus and fortunes. With CrusherTV Member, Brian Jordan.

Overwhelmed at work or home? Theres a 90% chance youre not delegating enough. And thats because you A) dont know what/to whom to delegate, B) dont know how to delegate smoothly, and/or C) havent calculated the massive benefits. Ill show you all three. With strengths coach Alissa Daire Nelson.

Overwhelmed at work or home? Theres a 90% chance youre not delegating enough. And thats because you A) dont know what/to whom to delegate, B) dont know how to delegate smoothly, and/or C) havent calculated the massive benefits. Ill show you all three. With strengths coach Alissa Daire Nelson.

We all have at least one big idea we want to move forward, or a major project we wish we could finally FINISH! Maybe youve got a bunch. Ill share evidence-based ways to re-start and rejoice in the finishing of your biggest, scariest projects. With rituals guru Craig Kulyk.

We all have at least one big idea we want to move forward, or a major project we wish we could finally FINISH! Maybe youve got a bunch. Ill share evidence-based ways to re-start and rejoice in the finishing of your biggest, scariest projects. With rituals guru Craig Kulyk.

We all have at least one big idea or project we want or need to start. But too often, they languish, un-started. Ill show why youre stuck and evidence-based ways to get going on your biggest, scariest idea/project. Plus, coach Lynne Edris shares keys to your Unique Operating System.

We all have at least one big idea or project we want or need to start. But too often, they languish, un-started. Ill show why youre stuck and evidence-based ways to get going on your biggest, scariest idea/project. Plus, coach Lynne Edris shares keys to your Unique Operating System.

We all have at least one big idea we want to start, but that sits collecting dusteven though its a GREAT idea. Ill share the secrets of what to do when you have a big idea: why its stuck and how to launch into it. With Dr. Sharon Saline.

We all have at least one big idea we want to start, but that sits collecting dusteven though its a GREAT idea. Ill share the secrets of what to do when you have a big idea: why its stuck and how to launch into it. With Dr. Sharon Saline.

Feeling happy right now? Or, if as is more likely, are you working hard, waiting until some happiness arrives? Were mostly doing the latter. But there are 5 simple ways to be (genuinely) happy right here & now & any time. With guest Dan Fowler, The Imagination Engineer.

Feeling happy right now? Or, if as is more likely, are you working hard, waiting until some happiness arrives? Were mostly doing the latter. But there are 5 simple ways to be (genuinely) happy right here & now & any time. With guest Dan Fowler, The Imagination Engineer.

Nobody who ever gave his best regretted it. Great quote. But how many of us feel we are at our best right now? And how can we BE at our best more often? Ill share 3 of the simplest/easiest ways. Plus, Minette Riordan shares the power of intentional distractions.

Nobody who ever gave his best regretted it. Great quote. But how many of us feel we are at our best right now? And how can we BE at our best more often? Ill share 3 of the simplest/easiest ways. Plus, Minette Riordan shares the power of intentional distractions.

Your to-do list is secretly killing your productivity in several ways. In fact, youre better off without one. Ill explain why, and how to make yours disappear. Also, YouTube phenom Jessica McCabe shares important distinctions to consider as you stare at your long to-do list.

Your to-do list is secretly killing your productivity in several ways. In fact, youre better off without one. Ill explain why, and how to make yours disappear. Also, YouTube phenom Jessica McCabe shares important distinctions to consider as you stare at your long to-do list.

Sadly, were all wasting tons of precious energy on negative BS. But what if you could double the mental energy you devote to thoughts and actions that move you forward? Ill show simple switches to turbocharge your thoughts and have more positive energy. With Guest Expert Dr. Colleen Mullen.

Sadly, were all wasting tons of precious energy on negative BS. But what if you could double the mental energy you devote to thoughts and actions that move you forward? Ill show simple switches to turbocharge your thoughts and have more positive energy. With Guest Expert Dr. Colleen Mullen.

I just LOVE CrusherTV - the videos are just the perfect combination of humour & excellent content and just the right length. Please pass on my thanks to all involved!! And please keep up the great work!!

Alan has helped thousands get more done in less time with less stress. A #1 Best Selling author and mess-to-success entrepreneur, he overcame a learning disability and drug addiction using his practical Zen brain hacks. As host of CrusherTV, Alan will teach you these and other evidence-based productivity hacks from top performers.

candy crush saga level 2699 help, solutions and more gogamerez

candy crush saga level 2699 help, solutions and more gogamerez

Here you will find information for how to clear Candy Crush Saga Level 2699. We have included videos for Candy Crush Saga 2699 Level with all Help, Solutions, hints, strategy and walk-through to clear Level 2699 of Candy Crush Saga. This game is developed by King. Please note Level 2699 is tricky, difficult and challenging. No of stars Required One

Blockers present in Level 2699 of Candy Crush Saga 1) In Candy Crush Saga Level 2699 you can clear frosting by making match to adjacent Candies. 2) In level 2699 Candy Crush Saga you have a blocker called Dark Chocolate. Make sure you dont allow it to spread. 3) In Candy Crush Saga 2699 level matching adjacent Candies is the best way to deal with Licorice Swirl. 4) Match the bomb with Candies of the same color before the timer hits zero in level 2699. 5) Try to destroy the mixer with adjacent matches, wrapped or striped candy blasts in level 2699 Candy Crush Saga.

Next Candy Crush Saga Levels Candy Crush Saga Level 2700 Candy Crush Saga Level 2701 Candy Crush Saga Level 2702 Candy Crush Saga Level 2703 Candy Crush Saga Level 2704 Candy Crush Saga Level 2705 Candy Crush Saga Level 2706 Candy Crush Saga Level 2707

Supported Android or Apple Devices for Candy Crush Saga Level 2699 a) Android Devices Own a processor built on ARMv7 architecture Support OpenGL ES 1.0 Support a 310480 resolution or higher Run on Android OS 1.3 or higher b) Apple Devices iOS version 6.0 or later on the following models: iPhone 4S, iPhone 5, iPhone 5s, iPhone 6 and later models iPad 1 and later models iPad Mini iPod Touch 4th generation and later

More Levels Candy Crush Saga Level 2708 Candy Crush Saga Level 2709 Candy Crush Saga Level 2710 Candy Crush Saga Level 2711 Candy Crush Saga Level 2712 Candy Crush Saga Level 2713 Candy Crush Saga Level 2714

I will update Gogamerez with more tips and tricks, so please bookmark Gogamerez.com. Surely, you can share your own stuff and help players unlock more goodies, levels, magic potions and earn stars. If you have any suggestions or questions, then do leave a comment and I or my friends and readers will answer them.

Candy Crush Saga Level 2715 Candy Crush Saga Level 2716 Candy Crush Saga Level 2717 Candy Crush Saga Level 2718 Candy Crush Saga Level 2719 Candy Crush Saga Level 2720 Candy Crush Saga Level 2721 Candy Crush Saga Level 2722

For the last three years, Ive been working at Gogamerez as an editor including blogging, article writing and conducting interviews. I am dedicated to helping independent video game developers reach massive audiences, publish financially successful titles and turn game development into a career.

Related Equipments