fryma mill msp 32 operating

used mill page 6 of 14 equipment machine for sale

used mill page 6 of 14 equipment machine for sale

There are many different names that are used to describe particle size reduction: milling, grinding, granulating, comminuting, etc. Milling systems can size reduce wet or dry powders. Their are variable speed drives that permit low speed screening and high speed impacting with one milling system. A typical milling system consists of an inlet chamber with a rotor screen and an outlet. The particle size depends upon the speed of the rotor, rotor type, screen hole size and the feed rate of the product. High shear granulation turns powders into dense granules for tableting or coating. Powders are added to a mixing bowl. A large impeller spins the powders into a vortex. A chopper tool shears the granules and removes the air. The granulated product is dried in the mixing bowl or fluid bed dryer.

Fitzmill, Model DKAS012, stainless steel hammer mill with pounds of product per hour depending on materials and application. Equipped with a 2"OD / 1"ID seated bevel style charge port, (32) 3" long x 1" wide fixed knife / impact blades and 3"OD / 3"ID Tri-clamp style discharge with 26" of ground clearance. Mounted on (4) leg painted frame base.

Quadro Model 197, 316 stainless steel particle size reduction Comil. Rated from 360 to 800 lbs of product per hour depending on materials and application. Equipped with 10" diameter x 6" deep stainless steel product hopper, 3" diameter feed throat, 5" diameter screen and 6" diameter discharge port with 26" ground clearance. Mounted on stainless steel (4) leg base frame. Discharge manifold with 5" OD connection for dust collection.

Fitzmill, Model DASO6, stainless steel hammer mill with production rates per hour depending on materials, application and machine configuration. Equipped with a 24" long x 20" wide x 4" deep feed pan, 6" wide x 4" high feed throat, 11 long x 6 wide blade chamber and (16) fixed knife/impact blades powered by a 7 Hp motor drive. Product discharge is 15 long x 5 wide with 36 floor clearance. Start / stop controls, mounted on (4) legs with casters.

Fryma vertical corundum stone colloid mill. Equipped 7" diameter stone, with 2-1/2" inlet/outlet. Used for grinding slurry / solids such as pigments, minerals, and fruit pulp to a fineness of 10-20 microns. Also used for dispersion/suspension of solids in liquids or pastes to a fineness of up to 1 micron. Rated 50 to 1000 liters per hour depending on materials, application and machine configuration.

Fitzmill, Model D, stainless steel hammer mill. Equipped with 12" long x 12" wide x 12" deep ( ft) product hopper, 3" diameter feed screw with 2" centers powered by HP drive with variable speed gearbox and (16) 3" long x 1" wide fixed knife / impact blades. Product discharge is 15L x 5 W with 36" of ground clearance. Mounted on (4) leg mild steel frame with casters.

Ross, 52C 6 x 14, Three roll mill rated up to 348 revolution per minute depending on materials and application Roller size" 14" in Length; 6" in Diameter. Equipped with 2 hp motor drive, steel mesh guarding, hand crank adjustable pressure, and a stainless steel discharge chute. Mounted on casters.

Greeco Model W250V colloid mill capable of complete dispersion and deagglomeration of liquids in liquids or solids in liquids at rates from 5 to 150 Gallons per hour depending on materials and application. Equipped with 12" diameter 5 gallon capacity 316 stainless steel hopper with recirculation pipe and bypass valve for multipass operation, truncated cone shaped 2-1/2" diameter rotor and a concave shaped stator. controller with start / stop controls and mounted on base frame. Used for cosmetics, emulsions, oils, dispersions, waxes and others

Heavy duty, mild steel, dual screen, hammer mill, with 576 sq inch screen area and up to 1740 rpm, production rates depending on materials and application. Equipped with a 13" x 9-1/2" OD, 9" x 6" ID top flanged product in feed with (8) 3/8" bolt holes on 5-1/2" centers, octagonal housing, 9" OD recessed reversible rotor with (8) 6" Long x 2" Wide knife / blunt swing blades. Side access doors with one piece, spring loaded, quick change screen carriage, drive shaft locking device, adjustable non leak air sweep, saftey and vibration sensor switches, 10" x 7-1/2" OD, 7" x 4-1/2" ID side bottom flanged discharge port with (6) 3/8" bolt holes on 4" centers, and 9" x 7" OD air relief port, 10 hp drive, and a start/stop control package. Mounted on heavy duty base frame.

Bliss Model E1906, Heavy duty, mild steel, dual screen, hammer mill, with 576 square inch screen area and up to 1740 rpm production rates depending on materials and application. Equipped with a 13" x 9-1/2" OD, 9" x 6" ID top flanged product in feed with (8) 3/8" bolt holes on 5-1/2" centers, octagonal housing, 9" OD recessed reversible rotor with (8) 6" Long x 2" Wide knife / blunt swing blades. Side access doors with one piece, spring loaded, quick change screen carriage, drive shaft locking device, adjustable non leak air sweep, saftey and vibration sensor switches, 10" x 7-1/2" OD, 7" x 4-1/2" ID side bottom flanged discharge port with (6) 3/8" bolt holes on 4" centers, and 9" x 7" OD air relief port, 10 hp drive, and a start/stop control package. Mounted on heavy duty base frame.

Stainless steel Fluid Air comminuting / hammer mill rated up to 6,000 RPM. Equipped with feed auger, reversing blade feature, dual frequency drives. Capable of handling both wet or dry products. Able to reduce to 40 microns. Results dependant on materials, application and machine configuration. Screens required per application. Mounted on casters.

Automatic, continuous operation, ultrafine wet grinding laboratory model. Has 1.2 liter 316 S/S product chamber, perforated 316 S/S disc agitator, jacketed chamber, 90-degree operating range, grinding media from 250 nano-meters to 2mm, 20 psi max grinding chamber, 45 psi max cooling system, S/S collecting pan for media, frictional gap size of 0.1 mm, E-stop, and variable frequency drive controller. Mounted on epoxy coated frame with casters.

mk (colloid mill)

mk (colloid mill)

The colloid mill MK 2000 is especially designed for the production of colloidal solutions, or extremely fine emulsions and suspensions. The high tip speeds, combined with an extremely small shear gap, produces intense friction on the material being processed. The friction and shear that result is commonly referred to as wet milling. The rotor and stator are cone shaped, and have three stages of increasingly fine serrations, or grooves. The stator can be infinitely adjusted to obtain the desired gap setting between the rotor and stator. The grooves change directions in each stage for increased turbulence. With high quality finishes and materials, the MK tool offers an extremely efficient milling geometry.

Related Equipments