mesh quartz grinding mills

grinding equipment_henan zhengzhou mining machinery co., ltd

grinding equipment_henan zhengzhou mining machinery co., ltd

Ceramic ball mill is also called (Intermittent ball mill/Batch ball mill). Ceramic ball mill can be used to grind feldspar, quartz, clay, silica and other hard brittle materials. It is widely applied in industrial production of high fine grinding materials.Ceramic ball mill grinding has dry and wet ways, of which the dry grinding can produce ultra-fine powder with the fineness of1000-16000 mesh.

The material goes to the first hopper after the spiraling by the quill shaft from the feeding equipment. The hopper has ladder sheathing or corrugated sheathing with steel balls inside, which will fall under the effect of centrifugal force by barrel turning to ram hard and grind material.

After the kibbling in the first hopper, by monolayer partition panel, the material will enter the second hopper, which has plane scale board with steel ball inside to grind material. The powder material will be discharged from the grid plate to finish the grinding.

laboratory ball mill

laboratory ball mill

A Laboratory Ball Millis used for grinding in laboratory flotation test work, wet grinding is necessary in several stages in order to approximate the actual grinding conditions of a ball mill and classifier in plant operation. With this small ball millit is possible to grind successfully in several stages without dilution, because the large feed opening and discharge hole (which retains the balls while the mill is being discharged) permits quick and thorough draining with the use of a minimum of wash water. Used in conjunction with a (Closed) Ball Mill, and a laboratory batch classifier saves time.

The (Open) Batch Mill makes possible simulation of grinding in a ball mill-classifier circuit by grinding a fixed time, then hand classifying with a sieve and a bucket and returning the sand to the mill for further grinding. Pulp volume can be kept at a minimum by control of wash water since the ball load does not dump out. Thus fine or coarse grinding is accomplished with ease of manipulation. The mill is used considerably as a regrind unit for further size reduction of flotation concentrates, table concentrates, middlings, and other mill products. Air may be introduced to the pulp, if desired, through theopen end of the cast steel drum.The (Open) Laboratory Ball Mill can beused for the amalgamation of table and flotation concentrates, by using one 4 ball during the grinding action.A few slight changes provide for mounting an Abbe Jar onthe driving shaft opposite the drum. This affords anexcellent combination laboratory grinding unit.

Laboratory Ball-Rod Mill is for grinding large quantities of ore in batch or continuous work. A grate discharge allows quick emptying for batch work; and a trunnion discharge, for continuous work. This flexible unit can also be used as an amalgamator.

The welded steel base can be provided in lengths suitable for supporting one, two, or three drums. One drum constitutes a ball mill; two, a rod mill; and three, a tube mill. The constructionpermits easy and rapid addition or removal of drums forconversion from one type to another, the trunnion being moved along the channels to accommodate the various lengths.The grinding drums are made with thick walls, thus eliminating the necessity of liners and the possibility of salting samples.This grinding mill has many commercial applications, since special acid resisting drums and heads can be furnished. Hard iron or alloy steel replaceable liners are easily inserted where wear is an item as in continuous use.

For continuous pilot test plants utilizing No. 7 or No. 8 Sub-A Flotation Machines, ball mills with larger grinding capacities are required. The 30 Convertible Ball Mill is ideal for this application. Capacity of this mill with single section is 3 to 5 tons per 24 hours while the double section mill, illustrated above, has a capacity of 6 to 9 tons per 24 hours.

The Buckboard and Muller ball mills are an extremely useful addition to most ore dressing or industrial laboratories. It accomplishes the quick reduction of small quantities of ore or other crushable materials to a fine powder. The unit consists of a chilled iron buckboard grinding surface, two sides of which are rimmed, and the desired type and weight of muller. Thebuckboard grinding surface is planed smooth and standard mullers have rounded crushing faces. Mullers may be purchased separately from either standard types shown or special from the three sizes of each type listed in the table and classified by rounded or flattened crushing faces. Rounded face mullers as listed have hickory axe type handles and flattened face mullers are equipped with hickory pick type handles.

MILL, Ball, Braun-WelschA laboratory ball mill particularly suitable for the metallurgical laboratory for flotation, cyanidation or amalgamation tests, but useful for any type of fine grinding. Will grind either wet or dry.

The ball mill body, or shell, is of gray cast iron, 12 inches inside diameter, 7 inches between the two machined driving ribs. Openings in the centers of heads allow free access of air during the grind, duplicating commercial scale plant conditions. The driving power is peripheral, applied frictionally through the supporting rollers. For loading, discharging and cleaning, the mill body is raised from the rollers by a rack and pinion device. This allows it to be turned, bringing its axis into the vertical position shown above. Removing the upper head by loosening five lug screws makes the inside completely visible and accessible. Pulp can be discharged through the lower opening, the balls being retained by a spider. Discharging and cleaning are rapid and thorough. All possibility of salting is eliminated, provided advantage is taken of the facilities for thorough cleaning.

The capacity is from 10 grams up to 12 pounds. Preliminary crushing to minus 10 mesh is recommended. The time for reducing an average sample to minus 65 mesh is about 15 minutes. Iron balls are used. The usual ball charge is 22 pounds, assorted sizes, 1, 1 and 2 inch being used. Steel rods 1 inch diameter may be used with good results. The mill operates at 50 R. P. M. and is driven by a 1/6 H. P. 110 volt, belt-connected motor. Mounted on steel table; floor space required, 30 x 30 inches. Height over all, 51 inches. Net weight, including balls, 270 pounds. Gross shipping weight, approximately 350 pounds.

A Ball Mill of Laboratory size, for grinding wet or dry material. Specially recommended for experimental flotation work where the oil or reagent is mixed with the samples, and gives results in harmony with those obtained in regular practice. Can be used for any type of fine grinding.

The maximum capacity is 25 pounds of ore. An assortment of iron balls inches, 1 inch and 1 inch sizes are included. The sample should be ground 20 mesh or finer (preferably with a Braun type U A Pulverizer) before being placed in the ball mill.

Designed for laboratory needs with ready access for charging and discharging the sample. The oval opening measures approximately 10 x 4 inches, and is large enough for all practical purposes. The receiving pan is in two parts, the upper portion being fitted with a screen to catch the iron balls while the ground materials fall through into the lower pan.

Ball Mill Dimensions: Cylinder, 12 x 12 inches ; floor space 27 x 13 x 22 inches ; pulley, 12 x 2 inches. Speed recommended, 40-50 RPM. Shipping weight, 300 pounds.Iron Balls, ExtraFor use with above.Receiving Pan, Extra.Source

The Abbe Pebble Mill is particularly adapted to pulverizing or mixing either dry or wet materials. This unit is of the batch or intermittent type. The cylinder is approximately half filled with flint pebbles, porcelain balls, or metal balls; the material is put into the cylinder; a tight cover is fastened securely, to seal the mill hermetically; and the cylinder is then revolved until the fineness required is obtained. After that the tight cover is replaced by a grate discharge cover and the cylinder is revolved until the material is discharged, the grate retaining the pebbles or balls. For dry grinding it is customary to enclose the cylinder to prevent the spread of undesirable dustand also to preserve all of sample to insure accuracy of testingprocedures.

In wet grinding, the same directions are followed except there is no casing required; and instead of replacing the tight cover with a grate cover, a special wet discharge cover, or the Abbe patented discharge valve, is used for emptying the mill.

The Abbe Laboratory Jar Mill pulverizes materials by friction and the fall of pebbles or balls contained within a rotating jar. In operation the jar is filled almost to the center plane with pebbles, and enough crushed material is added to fill the interstices between the pebbles and bring the charge to about 3/5 of the capacity of the jar. Usually a coarse screen is used to separate the pebbles from the material after grinding.

This unit is particularly adapted to pulverizing and mixing dry or wet materials and is manufactured in many sizes and styles for various capacities and conditions. Number of jars handled varies with mill size.

Jars are manufactured in many sizes and are of the best material. The three kinds available are: (1) Porcelain Jars carefully molded and fired to obtain the proper degree of vitrification so as to give acid and wear resisting qualities for grinding and agitation. (2) Metal Jarsmade of the metal most resistant to the action of a grinding charge, such as Monel, stainless steel, cast steel, and bronze. (3) Pyrex Jarsare transparent and enable observation during grinding or agitating action.

The Jar type Laboratory Ball Mill is ideal for use in pulverizing, mixing of dry and wet materials, and agitation of all types of pulps. Two large bottles or as many as six smallbottles can be used at the same time, thus providing a very flexible type of jar mill. When used for agitation, large ammonia bottles filled with pulp can be agitated continuously for any length of time.

The Laboratory Pebble Mill is a simple, efficient laboratory batch grinding unit. This machine is also an effective laboratory bottle type agitator for use on all types of pulps especially cyanide pulp. Two large bottles or jars or as many as six small jars may be used at the same time. This provides a wide range of capacity for batch laboratory grinding, and, at thesame time, affords a very flexible unit for batch agitation.The speed reducer and chain drive mechanism is positiveand the entire unit is mounted on a steel base. Idler rolleris adjustable to various bottle sizes. Data on jar sizes and types given under Laboratory Agitator, (Bottle Type).

Pulverizing is effected in these ball mills by the friction and fall of balls or pebbles contained within a rotating porcelain or glass jar. In general practice, the jar is filled to a little below the centre plane with pebbles; well crushed material then being added to fill the interstices and bring the charge to about three-fifths of the total space in the jar. After the operation, the pebbles and ground material are usually separated by means of a coarse grid.

Either hard or soft material may be ground, but it should not be moist to the extent that it will pack in the cylinder. If sufficient liquid is present, this method is superior to others for fine pulverization. Equipment is supplied complete with porcelain jar and flint pebbles.

A complete laboratory service that includes preliminary examination, batch or pilot-grinding test, open or closed circuit grinding, both wet and/or dryprovides important data for determining accurate mill size, for determining circulating loads, sizing accessories, grindability indexes and power requirements. Preliminary tests are made at no cost to you. Send 100 lb. sample of material prepaid.

Under the foregoing conditions experiments were designed to obtain data on (1) the relation of time of grind to mill output in g.p.m., and (2) the relation of mill output in g.p.m. to size of finished product. The relation of time of grind to mill output was studied by two procedures: (1) By a batch continuous grind technic and (2) by a batch cycle grind technic. The batch cycle grind technic is described in Part II of this Paper, Batch Closed-Circuit Grinding.

A short period of grind was selected, which far purposes of discussion can be assigned a value of x minutes. A number of individual 1,750-gram charges were weighed out. One of them was ground for x minutes, one for 2x minutes, one for 3x minutes, and so on up to 8x minutes.

The g.p.m. output of the mill for any x-minute time increment is readily calculated by simple arithmetic. If Wx is the weight of finished product resulting in the first x-minute grind, the g.p.m. output is Wx % x. If W2x is the weight of finished product produced in 2x minutes time, the mill output for the second x-minute increment is W2x Wx/x g.p.m., and so on.

It is obvious that the maximum percentage (by weight) of unfinished product (feed) is present in the mill when x is zero, and that although the mill load remains constant, the weight of unfinished feed starts diminishing at the initial turn of the mill. For this reason it was thought that in batch grinding, which may be assumed to compare in a limited way to open-circuit grinding, the efficiency of the mill possibly should be a maximum at the very initial revolution of the mill. This proved not necessarily to be the case, as may be seen by reference to the experimental data given.

The many missing links in the science of ball-mill grinding as revealed in mailing the study here presented and as brought out in the subsequent analysis of the experimental data, led to the studies by the author and H. E. Lee which are presented elsewhere under the title of Ball Mill Studies, Parts I, II, III, etc., and to Part II of this paper.

The condensed experimental data of this research and calculations based on these data are given in Table 1. The time of grind is given in vertical column 1. The sieve analysis of the product of each grind test is given, showing total grams, weight per cent, weight per cent cumulative, grams per minute, grams per minute cumulative, total surface, and total surface cumulative of each sieve size. There is also a horizontal column for each time, increment of grind, giving grams per minute cumulative for each three-minute grind increment throughout the entire 24-minute time, rangethat is, the g.p.m. output for the 0 to 3 minute period, for the 3 to 6 minute period, for the 6 to 9 minute period, and so on for each period.

Figure 1 shows the finished product-per cent of total mill charge plotted vertically against time of grind horizontally for each of the finished sizes considerednamely, 65, 100, 150, 200, and 250 mesh. These lines may be termed cumulative rate curves.

A set of tests similar to those previously described for quartz was made with Morning mine ore. The data are presented in Table 2. This ore is an aggregate largely of quartzite, siderite, sphalerite, and galena. These, data are shown graphically in Figure 4, in which finished product, g.p.m. is plotted vertically against time of grind increment horizontally. These curves indicate that at all sizes the highest rate of production of finished product is for the initial two-minute grind increment, except in the cases of the finished minus-48 mesh and minus-65 mesh products. In the absence of surface data, such as were calculated for quartz, it can not be known if the maximum finished product points for the minus-48 and minus-65 mesh sizeswhich occur at the second two-minute grind incrementsare due to increases in unfinished sand surface in the mill or to some other element.

The significant fact to note from this set of experiments is that finished product is made most rapidly at the very beginning of the grind. This suggests that in the practical closed-circuit plant the circulating load should be large in order to keep a high percentage of unfinished sand in the mill.

For quartz grinding to, say, finished minus-100 mesh sand, a 100 per cent circulating load should give approximate maximum efficiency. For Morning ore the circulating load should be high for maximum efficiency. The charge should not remain in the mill longer than two minutes, or possibly one minute. For this (two min.) length of grind for, say, finished minus-100 mesh product, 20.6 per cent of the charge is reduced to finished size. Therefore, for high efficiency, a circulating load of not less than 500 per cent is required. This corresponds closely to practice now in vogue in the Morning Mill, Mullan, Idaho, where this material is being milled. In designing a plant to treat a new ore, a test of this kind should be of much value in selecting the type of ball mill and classifier to be used. These experiments led to the batch closed-circuit experiments, which are to be described in Part II of this paper.

If the capacity of the mill used in these experiments be rated at one unit of finished minus-65 mesh product in a unit of time, its capacity to make finished product at any finer mesh may be calculated from Table I for quartz and from Table 2 for Morning ore. See Table 3.

These data show that the mill has four times as much capacity when grinding to finished minus-65 mesh as when grinding to finished minus-250 mesh. It has approximately three times as much capacity to produce finished minus-150 mesh Morning ore as finished minus-150 mesh quartz. These figures all are based on the output of the mill for the initial grind periodthree minutes for quartz and two minutes for Morning ore.

To learn if a greater mill output could be obtained than in any of the previous tests, an experiment was designed in which the period of grind was one minute. Quartz was used, and all other experimental conditions were the same as in previous experiments. At the end of each one-minute grind the charge was removed from the mill and the weight, in grams, of finished minus-100 mesh sand was determined. A quantity of new ore equal to the determined weight of finished product with the original charge was returned to the mill. The grind was conducted for another one-minute period. This process was repeated seven times, and each time enough new water was added to keep the water-ore ratio at 30:70 by weight. At seven new ore additions the mill became choked, and further additions could not be made.

The object in the plan of this experiment was to keep in the mill a nearly constant weight of unfinished feed, without removing the finished product. This procedure should, of course, result in high unfinished sand surface in the mill. The experimental data of this run are compiled in Table 4.

The output of finished minus-100 mesh sand produced the first minute is 175 grams; the output per minute for the first two minutes is 154 grams; for the first three minutes, 127 grams; for the first four minutes, 143 grams; for the first five minutes, 108 grams; for the first six minutes, 119 grams; and for the full seven minutes, 106 grams. On the basis of these figures the output is a maximum for the initial one-minute grind during, which only original feed is in the mill. Considered on the basis of output for each of the time increments, calculation shows that the output of the mill is greatest during the fourth minute grind increment, when 195 grams were produced. This result may be due to experimental error, and it is believed to be, for during the next minute (the fifth) increment the output is negative and for the sixth-minute increment the output is 166 grams. That the mill output was less for the third and fifth minute increments than for the fourth-minute increment is almost proof of experimental error, and the conclusion may safely be drawn that nothing is to be gained by overfeeding a ball mill, and that choking of the mill with finished product cuts down the mill efficiency.

contact winnermac

contact winnermac

Located at West High-Tech Development District, Zhengzhou City, Henan Province,Winnermac Heavy Industry inc is a technology-intensive enterprise, which integrates development, production and sales of mining,crushing and powder grinding machinery over more than 20 years. And we developed through innovation, and put into production officially in 1993. In Winnermac, we offer Integrated technology solutions with superior quality machines, which are at the cutting edge of the global mining and agricultural machinery landscape.Supported by decades of experience and in partnership with worldwide Toprank mineral processing and fertilizer production companies, Winnermac today is the leading machinery manufacutrer and solution provider. PRODUCT SCOPE The leading products include whole set Mineral Processing Equipment,Mineral Drying Machines,Powder Grinding Mills ,Stone/Sand Making machines and Fertilizer Production Machines. the Mineral Processing Equipments are Magnetic Separator, Rotary Dryer,Ball Mill, Shaking Table, flotation machine, Spiral Classifier,Jigger, etc. and those machines are applicable to select non-ferrous metal ore such as iron, copper, gold, silver, lead, tungsten, molybdenum, manganese and non-metal ores such as fluorite and quartz. The Mineral Drying Machines, which is includes ofRotary dryer,double drum rotary dryer,Three drum rotary dryer,Coal slime rotary dryer,Flyash rotary dryer,Fertilizer rotary dryer,Sand rotary dryer,Brown coal/lignite rotary dryer,Slag rotary dryer,Gypsum rotary dryer,Wood chips rotary dryer,Ore slurry rotary dryer,Stainless steel rotary dryer,Lime rotary kiln,Cement rotary kiln,Rotary kiln,Ceramsite rotary kiln,Sponge iron rotary kiln,Sawdust/wood powder dryer andMesh-belt dryer. Our Powder Grinding Mills which widely used in metallurgy, mining, chemical, cement, coal, sand-making, coal gangue, construction, refractory materials and ceramic industries, according to different material and fineness of final products, we can offer youGrinding Mill,Micro Powder Grinding Mill, Heavy calcium carbonategrinding mill, Limestone grinding mill, Gypsum stone grinding mill,HGM90 stone grinding mill, High pressure suspension grinding mill,Gangue grinding mills, Marble grinding mill, HGM100 grinding mill, Kaolin Grinding Mill ,Dolomite powder Mill, HGM125 grinding mill,ChinaGrinding Mill, European Version Fine grinding mill, HGM80 GrindingMill,ultrafine stone grind Grinding Mill,Raymond Roller Mill,etc Our Fertilizer Production Machines are composed of disc mixers, vertical crusher, disc granulator, rotary drum granulator, rotary dryer, rotary cooler, belt conveyor, elevator, packaging machines, high-temperature materials drying equipment and fertilizer coating machine. and Fertilizer machine is applicable to produce Organice and Inorganic fertilizer with high, medium and low content of fertilizers. HISTORY With 20 years of growth and development, we now have fixed assets amounting to RMBRMB103,260,000, 400 staffs and 80 technicians. We cover an area of 80,000 square meters,with a workshop area of 50,000 square meter. We have became a comprehensive enterprise that comprises scientific research, test, manufacture, and service departments. The products have won many awards of varied levels and passed the attestation of ISO9001 Quality Control System SGS of Sweden. Our clients spread all over the country. Products are sold to South Korea, Taiwan, Indonesia, Vietnam, Portugal, Germany and Middle East with the Annual export quantum composing one third of the total sales, wining praises from the purchasers. Sincerely welcome the friends from all over the world to our company for investigation and order. As a result of our continous efforts, our company has become one of the largest manufacturer and supplier of electromechanical equipments in similar industry of China. And we have a large variety of equipment with various specification, and our automation degree is very high. QUALITY,COST CONTROL In order to privede high-quality products and best service for our customers, we always insist on doing the following things: 1,Based on the national standards and requirements of production process, we have made our own quality stardards and also strictly adhere to those standards. All the processes from outsourced parts to the processing by ourselves are controlled by the quality control department. 2,All of our steel materials are purchased from famous Baosteel Group Company and Masteel Group Company in China, and after purchased, those steel materials should be thoroughly checked by our quality control department before putting into use. In this way, high quality of our products is guaranteed from the very beginning. 3,We have obtained certificates of ISO9001, ISO2000 and ABS. And in our production process, we strictly adhere to the ISO9001 quality management standards and carefully allocated physical recources and labor power to optimize the utilization of our resources

Over last 6 years, WinnerMac already sold her products to USA, Canada, Germany, United Kingdom, Denmark, Sweden, Poland, Italy, Greece, Australia, New Zealand, Japan, Korean, India, South Africa, and so on. We are always on the way, never stop.

ftm china quartz grinding mills with ce and iso - fote machinery

ftm china quartz grinding mills with ce and iso - fote machinery

Quartz sand and quartz powder can be got through the grinding process of quartz stone. Quartz powder making machine can grind the quartz stone into 30-120 mesh quartz powder. Ultrafine mill grind quartz stone into 325-3000 mesh quartz powder.

Quartz stone orejaw crusher small stone wheel grinding mill (powder grinding mill) sedimentation tank dryer dry sand vibrating screen iron removal products storage. Dry production process of quartz powder includes ordinary quartz powder and refined quartz powder, and the water production process is also divided into two types. Compared with the dry quartz powder, during the water production type of quartz powder, it produces less iron and the water can wash away the impurities, so its iron content and impurities are less than dry quartz powder. But because the water production process has high labor and material consumption, so the price is higher.

Related Equipments