ne bucket elevator

ne bucket elevator

ne bucket elevator

Model Capacity(m3/h) Max.particlesize(mm) Materialbulkdensity(t/m3) Max.liftingheight(m) MotorPower(kw) NE15 10-15 40 0.6-2.0 35 1.5-4 NE30 18.5-31 55 0.6-2.0 50 1.5-11 NE50 35-60 60 0.6-2.0 45 1.5-18.5 NE100 75-110 70 0.6-2.0 45 5.5-30 NE150 112-165 90 0.6-2.0 45 5.5-45 NE200 170-220 100 0.6-1.8 40 7.5-55 NE30 230-340 125 0.6-1.8 40 11-75 NE400 340-450 130 0.6-1.8 30 18.5-90 NE500 450-550 140 0.6-1.8 30 30-110 NE600 550-660 150 0.6-1.8 30 37-132 NE800 680-830 165 0.6-1.8 30 37-160

plate chain bucket elevator

plate chain bucket elevator

OverviewNE Bucket elevator is a kind of elevator used for lifting bulk materials vertically, maximum transport height is 50 m. It is widely used in the cement industry, chemical industry, power plant, grain storage and other industry etc, For conveying cement, cement clinker, crushed lime, sand, compound fertilizer, coal, grain and other bulk material etc. Our company manufacture various type bucket elevator to meet your different demands.All buckets are tracked by Steel Plate chain not belt, so it can resist high temperature more than 250. And the steel plate chain has a longer service life than belt.Operating PrincipleFlow-through feeding: Materials directly flows into the hopper which does not need to excavate materials, reducing mechanical wear.Materials are completely and uniformly taken, which avoid material storage at the bottom. It is suitable for conveying materials with large size and relatively high abrasiveness.Performance Features1. High Hoisting CapacityThe flow-through feeding and induction discharging are adopted, and the intensively arranged hopper is adopted for the conveying. The chain speed is low and the hoisting amount is large. The hoisting amount is within the range of 15-800 m3/h.2. Low Drive PowerWhen the material is hoisted, there is no back feed and packing, so the useless power is low. The theoretical calculated power is about 45% of that of the ring elevator.3. Wide Range of HoistingThis type of elevator poses fewer requirements for the type, characteristics and lumpiness of the material. It can hoist not only powdery, granular and block materials but also the materials with high abrasiveness and with a temperature of 250.4. Higher Lifting HeightWith low chain speed, smooth and steady operation, and high-strength wear-resisting plate chain, the hoisting height (up to 50m) is relatively large.5. Long Service LifeThe flow-through feeding is adopted for the elevator, and there is little squeezing and collision between moving parts and material. The elevator is designed to ensure that the material will not be scattered during feeding, hoisting and discharging, which prevents the elevator body from being worn by the material. The conveying chain is a high-strength wear-resisting plate chain that can extend the service life of the chain and chain bucket. According to the long-term production practice of the product. The service life of the conveying chain is over 5 years.6. Convenient MaintenanceThe advanced design principle ensures the operational reliability of the entire conveyor. The failure-free time is over 20,000 hours.Structural Composition1NE plate chain bucket elevator consists of running part, drive unit, head device, middle casing, and tail device.2Running part consists of a hopper and a bush roller chain. The single-strand chain is used for NE15 and NE30, and the double-strand chain is used for NE50-NE500.3Drive unit consists of a drive platform, a drive combination and a transmission chain. There are 2 types of drive combinations:1). Chain drive: it is generally composed of a hardened reducer (or JZQ speed reducer), a YOX hydraulic coupling, a Y-series motor, an XWD speed reducer, an electromagnetic clutch (or manual clutch);2). Direct connection: the direct connection is used between the rectangular-axis hardened reducer and the main shaft of the elevator, and the coupling connection is used between the Y-series motor and the speed reducer.4Drive device is divided into left assembly drive device, right assembly drive device, and dual drive device. So as to be respectively corresponding to left assembly elevator, right assembly elevator, and dual drive elevator.Left assembly: personnel are face to the feed inlet, while drive device combination is on the left side.Right assembly: personnel are face to feed inlet, while drive device combination is on the right side.Dual drive: personnel are face to the feed inlet, while drive device combination is on both sides.5Middle casing -middle nodules, standard and non-standard, of the access door, are included.6The tail device is equipped with a tension gear, the NE15-50 is spring-tensioned, and the NE100-500 is drop-weight-tensioned. At present, our company provides a new internal tension device, which will greatly reduce ash leakage.

NE Bucket elevator is a kind of elevator used for lifting bulk materials vertically, maximum transport height is 50 m. It is widely used in the cement industry, chemical industry, power plant, grain storage and other industry etc, For conveying cement, cement clinker, crushed lime, sand, compound fertilizer, coal, grain and other bulk material etc. Our company manufacture various type bucket elevator to meet your different demands.

The flow-through feeding and induction discharging are adopted, and the intensively arranged hopper is adopted for the conveying. The chain speed is low and the hoisting amount is large. The hoisting amount is within the range of 15-800 m3/h.

This type of elevator poses fewer requirements for the type, characteristics and lumpiness of the material. It can hoist not only powdery, granular and block materials but also the materials with high abrasiveness and with a temperature of 250.

The flow-through feeding is adopted for the elevator, and there is little squeezing and collision between moving parts and material. The elevator is designed to ensure that the material will not be scattered during feeding, hoisting and discharging, which prevents the elevator body from being worn by the material. The conveying chain is a high-strength wear-resisting plate chain that can extend the service life of the chain and chain bucket. According to the long-term production practice of the product. The service life of the conveying chain is over 5 years.

2). Direct connection: the direct connection is used between the rectangular-axis hardened reducer and the main shaft of the elevator, and the coupling connection is used between the Y-series motor and the speed reducer.

Drive device is divided into left assembly drive device, right assembly drive device, and dual drive device. So as to be respectively corresponding to left assembly elevator, right assembly elevator, and dual drive elevator.

Thanks for your time and interest in Yingda Heavy Industry .We are focus on what we really can do for our customers . So , if you have more detailed information , please feel free to let us know . We will reply you within 24 hours .

ne series bucket elevator plate chain-zhejiang province jiande conveying machinery equipment co., ltd

ne series bucket elevator plate chain-zhejiang province jiande conveying machinery equipment co., ltd

1. TB-NE series board chain hoist (hereinafter referred to as NE series board chain hoist) is the introduction of foreign advanced technology similar products developed products. It is currently a more advanced and mature vertical lifting equipment, has been widely used to enhance a variety of bulk materials, such as: ore, coal, fly ash, cement, cement clinker, grain, fertilizer and the like. In the industrialized countries, such hoist a very wide application. Due to its high efficiency, it has become an alternative choice for HL and TH type and so ring chain hoist.

2.1 to enhance a wide range: such hoist on the kind of material, less required characteristics and block degree. Not only can improve powdery, granular and bulk materials, but also to enhance the abrasive big material and temperature of the material 250 .

2.3 Long life: feeding hoist to take inflow, squeeze and collision phenomenon rarely occurs between moving parts and materials, the machine is designed to ensure that the material in the feed, lifting and unloading will not scattered, which to prevent wear and tear on the body of material, the use of plate chain conveyor chain of high strength wear-resistant, extend the service life of the chain and chain bucket. According to the foreign like product in the production of long-term practice shows that conveyor life of more than five years.

2.4 drive power is small: this type of hoist to take into the feeder, gravity induction discharge, and the use of large-capacity hopper-intensive layout conveying chain speed is low, and enhance the capacity. When the material hoist, almost no feed back and excavating, therefore, less power is invalid, theoretical shaft power is about 45 percent chain hoist.

5.2 drives - taking Y series motor, through reducer (or geared motor directly cycloid) and chain drive components. (Can also be directly connected to the transmission gear according to user requirements to switch hollow shaft).

ne plate chain bucket elevator-nantong sunlike building materials technology co.,ltd

ne plate chain bucket elevator-nantong sunlike building materials technology co.,ltd

Characters and technical requirments of type NE,NSE series chain bucket elevator The material flow through the conveyor while feeding, avoiding squeezing and crashing between conveyor and material. Thus it runs stably with convenient maintenance. The conveyor is linked to the plate chain instead of linking points by points. Thus the using life is increased and it can over five years. The material flow through the buckets while feeding and it is guided by gravity while discharging. The buckets speed is very high (15-30m/min). The power when there is without feeding back of material is just 40% of common bucket elevator. The driving efficiency is high and It can run for over 30 thousand hours without any obstacles. Big conveying capacityThe conveying range is from15-800m3/h. Good sealing capacity and less environment pollution. Easily operation and maintenance, few easily worn-out parts. Abrasion resistant bucket with high filling rate Material of bucket:16Mn abrasion resistant plate. Filling rate of the bucket:75%-90%Confirmed by the speed and material Abrasion plate with material in. Two pieces of wing plate extending from the side plate, guiding material when feeding and discharging. Protective full welding with CO2 molding bed. Four holes connecting with chain are punched into the form. Alloy steel wear sleeve rolling chain Quality material selected from special steel plant with advanced heat treatment technology 1Inside and outside chain plate:40Cr 2Pin shaft :20CrMnMo 3Sleeve :20CrMo 4Roller:20CrMo Hardening and tempering HB293-365 Carbon and nitrogen carburization0.5mm), Quenching HRC55-62 Carbon and nitrogen0.5mm) quenching HRC55-60 Carbon and nitrogen0.5mm) quenching HRC50-55 heat treatment equipment with Net automatic-turning bag imported from Germany, carburized quenching deeply and evenly. 1Pin shaft and outside chain plate are fixed. The sleeve and inside chain plate can effectively reduce the abrasion of loading parts. 2The clearance fit between pin shaft and sleeve, between roller and sleeve is different according to the material, avoiding the abrasion to chains and the lengthening of the pitch. 3External chain plate is punched into bending plate structure. And it is convenient to fix the buckets and it can reduce the occupying space of laoding parts. Common inspection and break tension inspection test are used. It fully guarantees the technology requirements. Tail chain wheel MaterialZG35Mn Technical figuresfine turning with nimbus and no tooth Heat treatmentMiddle frequency quenching HRC55-60. . Tail wheel teeth can prevent abrasion and the inconformity of the chain between the head and the tail. NENSE Series plate chain bucket elevator NENSE series plate chain bucket elevator suits to vertically lift different kinds of material from powder to lumps. The material will flow through the buckets instead of the traditional pulling-out feeding. It is a replace of traditional bucket elecvator. Technical parameter of lifting chain Type Pitch External dia. Of roller Dia. Of pin shaft Length of pin shaft Internal pitch and internalwidth Thickness of chain plate Width of chain plate Breaken loader(T) NE15 101.6 26.5 11.5 70 27 6 35 10 NE30 152.4 36 15.5 90 36.5 8 50 24 NE50 152.4 36 15.5 90 36.5 8 50 24 NE100 200 44.5 19.1 120 51.8 10 60 38 NE150 200 44.5 19.1 120 51.8 10 60 38 NE150 () 200 48.5 22.2 126 57.6 10 75 55 NE200 250 63.5 31.75 146 67.4 12 90 75 NE300 250 63.5 31.75 146 67.4 12 90 75

Type Pitch External dia. Of roller Dia. Of pin shaft Length of pin shaft Internal pitch and internalwidth Thickness of chain plate Width of chain plate Breaken loader(T) NE15 101.6 26.5 11.5 70 27 6 35 10 NE30 152.4 36 15.5 90 36.5 8 50 24 NE50 152.4 36 15.5 90 36.5 8 50 24 NE100 200 44.5 19.1 120 51.8 10 60 38 NE150 200 44.5 19.1 120 51.8 10 60 38 NE150 () 200 48.5 22.2 126 57.6 10 75 55 NE200 250 63.5 31.75 146 67.4 12 90 75 NE300 250 63.5 31.75 146 67.4 12 90 75

bucket elevator, bucket elevators, bucket elevator manufacturer henan excellent machinery co.,ltd

bucket elevator, bucket elevators, bucket elevator manufacturer henan excellent machinery co.,ltd

Equipment model: TDG1000-42.50 Handling material: cement clinker Handling capacity: 650t/h Bucket width: 1000mm C-C distance: 42.50m Bucket speed: 1.86m/s End user name: Xuzhou (CUCC) Cement Co.,Ltd

Equipment model: TDG500-26.50 Handling material: Fertilizer Handling capacity: 150t/h Bucket width: 500mm C-C distance: 26.50m Bucket speed: 1.68m/s End user name: Yunnan Yuntianhua Co., Ltd

bucket elevator from agico bucket elevators manufacturer

bucket elevator from agico bucket elevators manufacturer

Bucket elevator is used to vertically lift mashed limestone, coal, gypsum, clinker, dry clay and other block granular materials and raw materials, cement, pulverized coal, and other powder materials. According to the running speed of buckets, bucket elevators can be combined with centrifugal discharge type, gravity discharge type and mixed discharge type. Centrifugal unloading type has a fast bucket speed and is suitable for conveying powdery, granular, small pieces and other abrasive materials; gravity unloading type has a slower bucket speed and is suitable for the lower section with a tensioning drum; mixing unloading type is suitable for conveying loose density <1.5t/m3 powder. There are few sprinkles during the loading and unloading, which reduces mechanical wear. The traction members of the bucket elevator have a chain, a NE plate chain bucket elevator, a plated chain, and a tape. The structure and manufacture of the chain are relatively simple, and the connection with the hopper is also very strong. When the material with large abrasiveness is conveyed, the wear of the chain is small, but its own weight is large. The structure of the plate chain is relatively firm and the weight is light. It is suitable for lifting hoists with large lifting capacity, but the hinged joint is easy to be worn. The structure of the tape is relatively simple, but it is not suitable for conveying materials with large abrasiveness. The temperature of the ordinary tape material does not exceed 60. C, the clamp steel tape allows the material temperature to reach 80 C, the heat-resistant tape allows the material temperature to reach 120 C, and the temperature of the material transported by the chain and the chain can reach 250 C.

Multiple drive combination (depending on the actual needs of the user). The drive platform is equipped with a maintenance frame and railings. The drive system is divided into the left assembly and right assembly.

The TH series bucket elevator is a commonly used lifting device. The bucket elevator uses a forged chain as the transmission part and has strong mechanical strength. It is mainly used for lifting powder and small particles and small blocks. Different from the TD series bucket elevators, the lifting amount is larger and the operation efficiency is higher. It is often used for the lifting of materials with a large specific gravity.

The NE series plate chain bucket elevator is a new type of bucket elevator. It adopts the plate chain transmission, which is different from the old model TB series plate chain bucket elevator. Its naming method is named after the lifting amount instead of the bucket width. For example, NE150 refers to a lifting capacity of 150 tons an hour instead of a bucket width of 150. NE series bucket elevators have high hoist efficiency, and there are NSE models and high-speed chain bucket elevators depending on the speed of the upgrade.

The TG series bucket elevator is a reinforced belt bucket elevator, which is different from the TD series bucket elevator. The TG series bucket elevator uses steel wire tape as the transmission belt, which has stronger transmission capacity. This series of bucket elevators has been used in grain transportation and has long been called a grain-specific bucket elevator.

ne, nse plate chain bucket elevator-ne, nse plate chain bucket elevator-cmhe

ne, nse plate chain bucket elevator-ne, nse plate chain bucket elevator-cmhe

StructureComposed of wheel hub and gear girth. Materialwheel hub ZG45Gear girth 20CrMo forging steelhigh strength and reamed bolt.Technical figurelow speed with12 toothHigh speed with 24 tooth. Manufacture wayLinear cutting and manufactured in a whole part and at the same time. Cut it after installation. The way of heat treatmentHardening and tempering of wheel hub is HB217-255Rgidity of gear girth hardening is HRC55-60

NENSE Series plate chain bucket elevator NENSE series plate chain bucket elevator suits to vertically lift different kinds of material from powder to lumps. The material will flow through the buckets instead of the traditional pulling-out feeding. It is a replace of traditional bucket elecvator.

bucket elevator chains - sun field machinery

bucket elevator chains - sun field machinery

A bucket elevator is usually a conveyor during which buckets are set up on the vertically circulating chain, to vertically convey loads of granular powder. You can find two series of bucket elevators: NE Sort (typical velocity) and NSE Variety (large speed). Both forms have wide-ranging applications.(a) NE Bucket Elevator ChainsAn NE style bucket elevator is really a general-use bucket elevator that operates at a usual conveyance speed. The elevator is produced with two kinds of chains: Common Conveyor Chain with Attachment G4 (typical or heavy-duty) and DK Robust Z Conveyor Chain.(b) NSE Bucket Elevator ChainsAn NSE variety bucket elevator is created for substantial velocity conveyance and the velocity is about double that of NE type. To withstand high speed operation and also to lessen noise and shock, the chain pitch is one-half or less of that of the chains for NE kind. To be sure higher sturdiness, pins, bushings and rollers are the similar as people for powerful Z-type.Make use of the sprockets exclusive for NSE Bucket Elevator Chains.

Related Equipments