open circuit primary ball mill for wet grinding mini

closed circuit grinding vsopen circuit grinding

closed circuit grinding vsopen circuit grinding

The simplest grinding circuit consists of a ball or rod mill in closed circuit with a classifier; the flow sheet is shown in Fig. 25 and the actual layout in Fig. 9. This single-stage circuit is chiefly employed for coarse grinding when a product finer than 65 mesh is not required, but it can be adapted for fine grinding by substituting a bowl classifier for one of the straight type so as to enable the W/S ratio of the overflow to be kept below the 4/1 limit usually necessary for flotation. On account of the greater efficiency of the bowl classifier the trend of practice is towards its installation in plants grinding as coarse as 65 mesh.

Single-stage grinding is generally to be recommended for small plants on account of its simplicity. Variations in the size and character of the ore are unavoidable in most plants, but they are, as a rule, very much more noticeable when operations are on a small than when they are on a large scale. Multi-stage grinding as practised in large installations may, therefore, prove impossible to control on a very small scale, and for this reason the simplicity of single-stage grinding is likely to result in a greater overall efficiency than would be obtained with a multi-stage arrangement. When, however, the capacity of a plant approaches or exceeds 1,000 tons per day, two-stage grinding becomes preferable because the effect of normal variations of the ore is less marked and control becomes correspondingly easier.

The usual type of two-stage circuit is shown in Fig. 26, and is one that can be employed for any degree of grinding, although a straight must be substituted for a bowl classifier in the second stage when a 48-mesh product is required. It used to be the practice at one time to omit the first classifier and to pass the feed straight through the primary mill to the secondary circuit, but it was not a good method because either the secondary mill received pieces of ore that were too big or else the primary mill overground a large proportion of the feed. Much better results are obtainable by keeping the coarse ore circulating round the primary circuit, which is set for the efficient grinding of such material, until it is fine enough to be sent to the secondary circuit where the machines are set to grind fine ore more efficiently than coarse. It should be noted that the overflow of the primary classifier is sent to the secondary classifier, not direct to the mill, in order that all material which has been ground fine enough in the primary circuit can be discharged immediately without any chance of its entering and being overground in the secondary ball mill.

So important is it from the point of view of efficiency to get the undersize out of the circuit at the earliest possible moment, whether it is produced in the primary or in the secondary mill, that a special intermediate bowl classifier is often installed between the two stages. Such an arrangement has been found very useful in plants in which improvements in dry crushing practice have resulted in a reduction in the size of the feed to the grinding mills with the result that they have been able to take larger tonnages; the classifiers have then becomeoverloaded, especially in the case of older installations in which both stages were equipped with straight classifiers.

The method of installing a bowl classifier to overcome the difficulty is shown in Fig. 27. This circuit is usually adopted in modern practice, but with a bowl instead of a straight classifier, if necessary, in the closed circuit of the secondary ball mill.

Any increase in the efficiency of classification gives greater economy of power by reducing the amount of ore that is overground, so making a larger proportion of the power required to turn the mill available forgrinding the particles that are still too large. From a theoretical point of view, the ideal method of grinding would consist of a series of ball mills, each in closed circuit with a classifier and each so short that the ore in its passage through the mill would be struck only two or three times by the balls, any undersize produced being removed at once by the classifier ; in this way the chance of a particle being struck again after it had reached the required size would be reduced to a minimum. Practice circuit design approaches the ideal:

Open circuit grinding consists of one or more grinding mills, either parallel or in series, that discharges a finalground product without classification equipment and no return of coarse discharge back to the mill. Some very simplistic examples of open circuit grinding are see below and are made of aRod mill,Ball Mill or aRod mill, ball mill combination.

Not all ores can be ground in an open circuit type ofarrangement. Some conditions which do favor open circuit grinding such assmall reduction ratios,reduction of particles to a coarse, natural grainsize,recirculation of cleaner flotation middlings forregrinding anda non-critical size distribution of the final groundproduct.

Closed circuit grinding consists of one or more mills discharging ground product to classifiers which in turn return the coarse product from the size separation back to the mill for further grinding. In this circuit, grinding efficiency is very dependent upon the size separation effected so care should be exercised in selecting the type and size of classifier used to close the system.

This type of grinding is the most common circuit found in mineral processing facilities, mainly because a lot of ores and product requirements are not suitable for open circuit grinding. Some advantages presented by grinding in closed circuit are that this arrangement usually results in higher mill capacity and lower power consumption per ton of product, it eliminates overgrinding by removing fines early and it avoids coarse material in the final ground product by returning this material to the mill.

Although closed circuit grinding offers many choices for arrangement of the equipment as well as combinations of equipment, some of the more common circuits arerod mill/classifier,Ball mill/Classifier,Rod mill/Ball mill/Classifier and Rod mill/Classifier/Ball mill/Classifier.

The importance of the grinding circuit to overall production in any facility should be obvious by now. Because of the responsibilities assigned to grinding it becomes essential that a grinding mill accepts a certain required tonnage of ore per day while yielding a product that is of a known and controllable particle size. This leads to the conclusion that close control over the grinding circuit is extremely important.

There are many factors which can contribute to fluctuationsin performance of a mill, but some of the most common found inindustrial practice are thechanges in ore taken from different parts of the mine,changes in crusher settings,wear in the crushers,screen damage in the crusher circuit.

These are a few things that operators should look for when changes in mill performance are noticed. Stockpiling of ore ahead of the mill can aid in smoothing out some of the fluctuations although it must be stored in such a manner that no segregation occurs.

The reduction ratio in the grinding section is so much greater than in the crushing plant that labour becomes a relatively small item and the power and steel consumption the largest items of cost. Table 18 gives the average total consumption of power that may be expected in modern ball mill installations of various capacities up to 4,000 tons per day, the figures being based on an average medium-hard ore.

The cost of grinding is more difficult to predict than that of crushing because variations in the hardness and toughness of the ore produce proportionately wider variations in the consumption of power and steel. An approximate guide to grinding costs; they are direct costs and include no overhead charges. Power is assumed to cost 0.075 per kilowatt-hour in the case of the smallest plant and to decrease to a minimum per kilowatt-hour for the largest.

As the tonnage rises up to 1,000 tons per day the costs fall rapidly. In plants of greater capacity, however, they do not decrease in the same proportion with increase of tonnage, because the extra capacity is not obtained by increasing the size of the individual machines but by installing two or more similar units side by side, each of equal efficiency.Reduction of costs then becomes more a matter of organization than of plant design.

As already stated, the power and steel costs are the two largest items, those of labour and supplies being small by comparison ; it is on this account that recent progress has been mainly directed towards reducing the consumption of power and steel by means of greater efficiency in classification and by the use of mills of larger diameter.

The way in which the efficiency of classification has been increased has been described in the paragraph headed Grinding Circuits. An increase in the diameter of a mill gives greater economy in two ways : In the first place, the balls do more effective work in a large than in asmall mill, because, falling from a greater height, they shatter the pieces of ore with greater force ; in the second place, the ratio of the deadweight of the mill to the weight of the ball charge decreases as the diameter increases and thus in a large mill the useless weight to be moved is distributed over a greater weight of useful ball load than in a small mill, with the result that a larger proportion of the total power consumption is available to give the balls the cascading and rolling action necessary to break up the ore.

It is essential for the grinding and flotation sections of a plant to be run continuously. It takes nearly half an hour to clear the circuit of even a small grinding unit preparatory to stopping it, and often an hour is necessary to get the circuit fully loaded after restarting ; most of the power required to keep the machines running during the stopping and starting periods is wasted. Moreover, the operation of the flotation machines is poor during these periods so that much of the power required to keep them running is also wasted. In addition, modern practice aims at the elimination of everything likely to cause fluctuating conditions. For these reasons it is the universal custom to run the grinding and flotation plants for 24 hours per day.

simple grinding circuits & flowsheets

simple grinding circuits & flowsheets

To start the discussion on grinding circuits I would like to begin by showing you some simple Flowsheet SCHEMATICS of some sample circuits, but before I do there is one thing that I must explain for the schematics to make sense. When the ore is put into the first piece of equipment for grinding, water is added to it to form a SLURRY. This water addition is very important, it makes the rest of the separation process possible as you will see a little later.

To design a circuit there is some information that has to be learned. The HARDNESS OF THE ORE, the TONNAGE that has to be ground per hour and the DEGREE TO WHICH IT MUST BE GROUND. Once these three pieces of information has been discovered the design of the circuit can begin. The four circuits that I am going to show you start with the simplest, the one that is grinding the softest ore to the coarsest grind.

The ore is simply brought from the fine ore storage area and run into one end of the grinding machine called a MILL, the mill grinds it and mixes it into a slurry which is sent to the next stage of processing.

Our second flow sheet, has a couple extra pieces of equipment added. These are a PUMP and a CLASSIFIER, A classifier is a piece of equipment that separates ground material by size, There are different methods that can be employed to accomplish this, but again that is something that we .will take up in greater detail in further sessions.

This is the path that the ore takes in this circuit. The ore comes from the fine ore storage area to be added to the mill. Again it is ground but this time the ground material is pumped to a classifier to be classified by size. The material that has not been ground enough will be sent back to the mill for regrinding. The material that is ready for the next phase of processing will be sent there.

That brings us to our third circuit. Like the second one, the ore is ground in a mill and sent by way of a pump box to a classifier. Now however there has been a second mill added. The rock that requires further grinding is sent to this mill where it is reground. Once the ore has gone through the mill, it is sent by way of the pump back for reclassification.

These circuits have been getting more and more complex. This is because the ore and the required grind has been getting more and more complicated. The ore in the first one was the softest and the grinding wasnt critical. In the second one the ore was probably still very soft, but the grind had become critical, therefore it had to have a positive control on it, hence the classification. The third one however has harder ore with a critical grind.

Now for our fourth and final flow sheet. This is one that has been-designed for exceptionally hard ore and/or a grind that must be very fine. This time the ore is conveyed to the first mill, mixed with water and ground. As it exits the mill it is separated and sent to two different pumps which in turn sends it to be classified. Each of the classifiers will send the material that requires grinding back to its own mill. On this circuit there was one PRIMARY MILL feeding two SECONDARY MILLS each with their own pump and classifier. Again the secondary mill discharge is sent back to its own classifier to be reclassified.

wet grid ball mill

wet grid ball mill

Grid ball mill is widely used in smashing all kinds of ores and other materials, ore dressing and national economic departments like building and chemical industries etc. The size of ore shall not exceed 65mm and the best feed size is under 6mm. The effect in this job is better than coarse grinding. Grid ball mill consists of the shell, feeding part, discharging part, main bearing, lubricating system, driving system and other parts. There is wearing a liner inside the shell, and both ends of the shell are provided with a flange. The end cover of the mill is connected with the flange plate. The feeding part consists of the head, trunnion and feeding device. The discharge part includes the grid plate, head, and discharge trunnion.

Wet Grid ball mill is mainly used for mixing and grinding materials in two types: dry grinding and wet grinding .It has advantages of fineness uniformity and power saving. The machine uses different types of liner to meet different customer needs. The grinding fineness of material can be controlled by grinding time. The electro-hydraulic machine is auto-coupled and decompressed to reduce the starting current, and its structure is divided into integral type and independent type.

Compared with similar products,Wet Grid ball mill has the characteristics of low investment, low energy consumption, novel structure, simple operation, stable and reliable performance. It is suitable for mixing and grinding ordinary and special materials. The users can choose the right type, liner and medium type by considering the specific gravity, hardness, yield and other factors. The grinding medium is Wet Grid ball.

1.The ball mill is composed of a horizontal cylinder, a hollow shaft for feeding and discharging, and a grinding head. The main body is a long cylinder made of steel. The cylinder is provided with an abrasive body, and the steel lining plate is fixed to the cylinder body. The grinding body is generally a steel ball and is loaded into the cylinder according to different diameters and a certain proportion, and the grinding body can also be used with a steel section.

2.According to the particle size of the grinding material, the material is loaded into the cylinder by the hollow shaft of the wet grid ball mill feeding end. When the ball mill cylinder rotates, the grinding body acts on the cylinder liner due to the action of inertia and centrifugal force and friction. It is carried away by the cylinder. When it is brought to a certain height, it is thrown off due to its own gravity. The falling abrasive body crushes the material in the cylinder like a projectile.

3.The material is uniformly fed into the first chamber of the mill by the feeding device through the hollow shaft of the feeding material. The chamber has a step liner or a corrugated liner, and various steel balls are loaded therein. The rotation of the cylinder generates centrifugal force to bring the steel ball to a certain extent. The height drops and then hits and grinds the material. After the material reaches the rough grinding in the first bin, it enters the second bin through the single-layer partition plate. The bin is embedded with a flat liner with steel balls inside to further grind the material. The powder is discharged through the discharge raft to complete the grinding operation.

The main function of the steel ball in the ball mill is to impact crush the material and also play a certain grinding effect. Therefore, the purpose of grading steel balls is to meet the requirements of these two aspects. The quality of the crushing effect directly affects the grinding efficiency, and ultimately affects the output of the ball mill. Whether the crushing requirement can be achieved depends on whether the grading of the steel ball is reasonable, mainly including the size of the steel ball, the number of ball diameters, and the ball of various specifications. Proportion and so on.

The ball mill is composed of the main part such as a feeding part, a discharging part, a turning part, a transmission part (a reduction gear, a small transmission gear, a motor, and electric control). The hollow shaft is made of cast steel, the inner lining can be replaced, the rotary large gear is processed by casting hobbing, and the barrel is embedded with wear-resistant lining, which has good wear resistance. The machine runs smoothly and works reliably.

ball mills

ball mills

In all ore dressing and milling Operations, including flotation, cyanidation, gravity concentration, and amalgamation, the Working Principle is to crush and grind, often with rob mill & ball mills, the ore in order to liberate the minerals. In the chemical and process industries, grinding is an important step in preparing raw materials for subsequent treatment.In present day practice, ore is reduced to a size many times finer than can be obtained with crushers. Over a period of many years various fine grinding machines have been developed and used, but the ball mill has become standard due to its simplicity and low operating cost.

A ball millefficiently operated performs a wide variety of services. In small milling plants, where simplicity is most essential, it is not economical to use more than single stage crushing, because the Steel-Head Ball or Rod Mill will take up to 2 feed and grind it to the desired fineness. In larger plants where several stages of coarse and fine crushing are used, it is customary to crush from 1/2 to as fine as 8 mesh.

Many grinding circuits necessitate regrinding of concentrates or middling products to extremely fine sizes to liberate the closely associated minerals from each other. In these cases, the feed to the ball mill may be from 10 to 100 mesh or even finer.

Where the finished product does not have to be uniform, a ball mill may be operated in open circuit, but where the finished product must be uniform it is essential that the grinding mill be used in closed circuit with a screen, if a coarse product is desired, and with a classifier if a fine product is required. In most cases it is desirable to operate the grinding mill in closed circuit with a screen or classifier as higher efficiency and capacity are obtained. Often a mill using steel rods as the grinding medium is recommended, where the product must have the minimum amount of fines (rods give a more nearly uniform product).

Often a problem requires some study to determine the economic fineness to which a product can or should be ground. In this case the 911Equipment Company offers its complete testing service so that accurate grinding mill size may be determined.

Until recently many operators have believed that one particular type of grinding mill had greater efficiency and resulting capacity than some other type. However, it is now commonly agreed and accepted that the work done by any ballmill depends directly upon the power input; the maximum power input into any ball or rod mill depends upon weight of grinding charge, mill speed, and liner design.

The apparent difference in capacities between grinding mills (listed as being the same size) is due to the fact that there is no uniform method of designating the size of a mill, for example: a 5 x 5 Ball Mill has a working diameter of 5 inside the liners and has 20 per cent more capacity than all other ball mills designated as 5 x 5 where the shell is 5 inside diameter and the working diameter is only 48 with the liners in place.

Ball-Rod Mills, based on 4 liners and capacity varying as 2.6 power of mill diameter, on the 5 size give 20 per cent increased capacity; on the 4 size, 25 per cent; and on the 3 size, 28 per cent. This fact should be carefully kept in mind when determining the capacity of a Steel- Head Ball-Rod Mill, as this unit can carry a greater ball or rod charge and has potentially higher capacity in a given size when the full ball or rod charge is carried.

A mill shorter in length may be used if the grinding problem indicates a definite power input. This allows the alternative of greater capacity at a later date or a considerable saving in first cost with a shorter mill, if reserve capacity is not desired. The capacities of Ball-Rod Mills are considerably higher than many other types because the diameters are measured inside the liners.

The correct grinding mill depends so much upon the particular ore being treated and the product desired, that a mill must have maximum flexibility in length, type of grinding medium, type of discharge, and speed.With the Ball-Rod Mill it is possible to build this unit in exact accordance with your requirements, as illustrated.

To best serve your needs, the Trunnion can be furnished with small (standard), medium, or large diameter opening for each type of discharge. The sketch shows diagrammatic arrangements of the four different types of discharge for each size of trunnion opening, and peripheral discharge is described later.

Ball-Rod Mills of the grate discharge type are made by adding the improved type of grates to a standard Ball-Rod Mill. These grates are bolted to the discharge head in much the same manner as the standard headliners.

The grates are of alloy steel and are cast integral with the lifter bars which are essential to the efficient operation of this type of ball or rod mill. These lifter bars have a similar action to a pump:i. e., in lifting the product so as to discharge quickly through the mill trunnion.

These Discharge Grates also incorporate as an integral part, a liner between the lifters and steel head of the ball mill to prevent wear of the mill head. By combining these parts into a single casting, repairs and maintenance are greatly simplified. The center of the grate discharge end of this mill is open to permit adding of balls or for adding water to the mill through the discharge end.

Instead of being constructed of bars cast into a frame, Grates are cast entire and have cored holes which widen toward the outside of the mill similar to the taper in grizzly bars. The grate type discharge is illustrated.

The peripheral discharge type of Ball-Rod Mill is a modification of the grate type, and is recommended where a free gravity discharge is desired. It is particularly applicable when production of too many fine particles is detrimental and a quick pass through the mill is desired, and for dry grinding.

The drawings show the arrangement of the peripheral discharge. The discharge consists of openings in the shell into which bushings with holes of the desired size are inserted. On the outside of the mill, flanges are used to attach a stationary discharge hopper to prevent pulp splash or too much dust.

The mill may be operated either as a peripheral discharge or a combination or peripheral and trunnion discharge unit, depending on the desired operating conditions. If at any time the peripheral discharge is undesirable, plugs inserted into the bushings will convert the mill to a trunnion discharge type mill.

Unless otherwise specified, a hard iron liner is furnished. This liner is made of the best grade white iron and is most serviceable for the smaller size mills where large balls are not used. Hard iron liners have a much lower first cost.

Electric steel, although more expensive than hard iron, has advantage of minimum breakage and allows final wear to thinner section. Steel liners are recommended when the mills are for export or where the source of liner replacement is at a considerable distance.

Molychrome steel has longer wearing qualities and greater strength than hard iron. Breakage is not so apt to occur during shipment, and any size ball can be charged into a mill equipped with molychrome liners.

Manganese liners for Ball-Rod Mills are the world famous AMSCO Brand, and are the best obtainable. The first cost is the highest, but in most cases the cost per ton of ore ground is the lowest. These liners contain 12 to 14% manganese.

The feed and discharge trunnions are provided with cast iron or white iron throat liners. As these parts are not subjected to impact and must only withstand abrasion, alloys are not commonly used but can be supplied.

Gears for Ball-Rod Mills drives are furnished as standard on the discharge end of the mill where they are out of the way of the classifier return, scoop feeder, or original feed. Due to convertible type construction the mills can be furnished with gears on the feed end. Gear drives are available in two alternative combinations, which are:

All pinions are properly bored, key-seated, and pressed onto the steel countershaft, which is oversize and properly keyseated for the pinion and drive pulleys or sheaves. The countershaft operates on high grade, heavy duty, nickel babbitt bearings.

Any type of drive can be furnished for Ball-Rod Mills in accordance with your requirements. Belt drives are available with pulleys either plain or equipped with friction clutch. Various V- Rope combinations can also be supplied.

The most economical drive to use up to 50 H. P., is a high starting torque motor connected to the pinion shaft by means of a flat or V-Rope drive. For larger size motors the wound rotor (slip ring) is recommended due to its low current requirement in starting up the ball mill.

Should you be operating your own power plant or have D. C. current, please specify so that there will be no confusion as to motor characteristics. If switches are to be supplied, exact voltage to be used should be given.

Even though many ores require fine grinding for maximum recovery, most ores liberate a large percentage of the minerals during the first pass through the grinding unit. Thus, if the free minerals can be immediately removed from the ball mill classifier circuit, there is little chance for overgrinding.

This is actually what has happened wherever Mineral Jigs or Unit Flotation Cells have been installed in the ball mill classifier circuit. With the installation of one or both of these machines between the ball mill and classifier, as high as 70 per cent of the free gold and sulphide minerals can be immediately removed, thus reducing grinding costs and improving over-all recovery. The advantage of this method lies in the fact that heavy and usually valuable minerals, which otherwise would be ground finer because of their faster settling in the classifier and consequent return to the grinding mill, are removed from the circuit as soon as freed. This applies particularly to gold and lead ores.

Ball-Rod Mills have heavy rolled steel plate shells which are arc welded inside and outside to the steel heads or to rolled steel flanges, depending upon the type of mill. The double welding not only gives increased structural strength, but eliminates any possibility of leakage.

Where a single or double flanged shell is used, the faces are accurately machined and drilled to template to insure perfect fit and alignment with the holes in the head. These flanges are machined with male and female joints which take the shearing stresses off the bolts.

The Ball-Rod Mill Heads are oversize in section, heavily ribbed and are cast from electric furnace steel which has a strength of approximately four times that of cast iron. The head and trunnion bearings are designed to support a mill with length double its diameter. This extra strength, besides eliminating the possibility of head breakage or other structural failure (either while in transit or while in service), imparts to Ball-Rod Mills a flexibility heretofore lacking in grinding mills. Also, for instance, if you have a 5 x 5 mill, you can add another 5 shell length and thus get double the original capacity; or any length required up to a maximum of 12 total length.

On Type A mills the steel heads are double welded to the rolled steel shell. On type B and other flanged type mills the heads are machined with male and female joints to match the shell flanges, thus taking the shearing stresses from the heavy machine bolts which connect the shell flanges to the heads.

The manhole cover is protected from wear by heavy liners. An extended lip is provided for loosening the door with a crow-bar, and lifting handles are also provided. The manhole door is furnished with suitable gaskets to prevent leakage.

The mill trunnions are carried on heavy babbitt bearings which provide ample surface to insure low bearing pressure. If at any time the normal length is doubled to obtain increased capacity, these large trunnion bearings will easily support the additional load. Trunnion bearings are of the rigid type, as the perfect alignment of the trunnion surface on Ball-Rod Mills eliminates any need for the more expensive self-aligning type of bearing.

The cap on the upper half of the trunnion bearing is provided with a shroud which extends over the drip flange of the trunnion and effectively prevents the entrance of dirt or grit. The bearing has a large space for wool waste and lubricant and this is easily accessible through a large opening which is covered to prevent dirt from getting into the bearing.Ball and socket bearings can be furnished.

Scoop Feeders for Ball-Rod Mills are made in various radius sizes. Standard scoops are made of cast iron and for the 3 size a 13 or 19 feeder is supplied, for the 4 size a 30 or 36, for the 5 a 36 or 42, and for the 6 a 42 or 48 feeder. Welded steel scoop feeders can, however, be supplied in any radius.

The correct size of feeder depends upon the size of the classifier, and the smallest feeder should be used which will permit gravity flow for closed circuit grinding between classifier and the ball or rod mill. All feeders are built with a removable wearing lip which can be easily replaced and are designed to give minimum scoop wear.

A combination drum and scoop feeder can be supplied if necessary. This feeder is made of heavy steel plate and strongly welded. These drum-scoop feeders are available in the same sizes as the cast iron feeders but can be built in any radius. Scoop liners can be furnished.

The trunnions on Ball-Rod Mills are flanged and carefully machined so that scoops are held in place by large machine bolts and not cap screws or stud bolts. The feed trunnion flange is machined with a shoulder for insuring a proper fit for the feed scoop, and the weight of the scoop is carried on this shoulder so that all strain is removed from the bolts which hold the scoop.

High carbon steel rods are recommended, hot rolled, hot sawed or sheared, to a length of 2 less than actual length of mill taken inside the liners. The initial rod charge is generally a mixture ranging from 1.5 to 3 in diameter. During operation, rod make-up is generally the maximum size. The weights per lineal foot of rods of various diameters are approximately: 1.5 to 6 lbs.; 2-10.7 lbs.; 2.5-16.7 lbs.; and 3-24 lbs.

Forged from the best high carbon manganese steel, they are of the finest quality which can be produced and give long, satisfactory service. Data on ball charges for Ball-Rod Mills are listed in Table 5. Further information regarding grinding balls is included in Table 6.

Rod Mills has a very define and narrow discharge product size range. Feeding a Rod Mill finer rocks will greatly impact its tonnage while not significantly affect its discharge product sizes. The 3.5 diameter rod of a mill, can only grind so fine.

Crushers are well understood by most. Rod and Ball Mills not so much however as their size reduction actions are hidden in the tube (mill). As for Rod Mills, the image above best expresses what is going on inside. As rocks is feed into the mill, they are crushed (pinched) by the weight of its 3.5 x 16 rods at one end while the smaller particles migrate towards the discharge end and get slightly abraded (as in a Ball Mill) on the way there.

We haveSmall Ball Mills for sale coming in at very good prices. These ball mills are relatively small, bearing mounted on a steel frame. All ball mills are sold with motor, gears, steel liners and optional grinding media charge/load.

Ball Mills or Rod Mills in a complete range of sizes up to 10 diameter x20 long, offer features of operation and convertibility to meet your exactneeds. They may be used for pulverizing and either wet or dry grindingsystems. Mills are available in both light-duty and heavy-duty constructionto meet your specific requirements.

All Mills feature electric cast steel heads and heavy rolled steelplate shells. Self-aligning main trunnion bearings on large mills are sealedand internally flood-lubricated. Replaceable mill trunnions. Pinion shaftbearings are self-aligning, roller bearing type, enclosed in dust-tightcarrier. Adjustable, single-unit soleplate under trunnion and drive pinionsfor perfect, permanent gear alignment.

Ball Mills can be supplied with either ceramic or rubber linings for wet or dry grinding, for continuous or batch type operation, in sizes from 15 x 21 to 8 x 12. High density ceramic linings of uniform hardness male possible thinner linings and greater and more effective grinding volume. Mills are shipped with liners installed.

Complete laboratory testing service, mill and air classifier engineering and proven equipment make possible a single source for your complete dry-grinding mill installation. Units available with air swept design and centrifugal classifiers or with elevators and mechanical type air classifiers. All sizes and capacities of units. Laboratory-size air classifier also available.

A special purpose batch mill designed especially for grinding and mixing involving acids and corrosive materials. No corners mean easy cleaning and choice of rubber or ceramic linings make it corrosion resistant. Shape of mill and ball segregation gives preferential grinding action for grinding and mixing of pigments and catalysts. Made in 2, 3 and 4 diameter grinding drums.

Nowadays grinding mills are almost extensively used for comminution of materials ranging from 5 mm to 40 mm (3/161 5/8) down to varying product sizes. They have vast applications within different branches of industry such as for example the ore dressing, cement, lime, porcelain and chemical industries and can be designed for continuous as well as batch grinding.

Ball mills can be used for coarse grinding as described for the rod mill. They will, however, in that application produce more fines and tramp oversize and will in any case necessitate installation of effective classification.If finer grinding is wanted two or three stage grinding is advisable as for instant primary rod mill with 75100 mm (34) rods, secondary ball mill with 2540 mm(11) balls and possibly tertiary ball mill with 20 mm () balls or cylpebs.To obtain a close size distribution in the fine range the specific surface of the grinding media should be as high as possible. Thus as small balls as possible should be used in each stage.

The principal field of rod mill usage is the preparation of products in the 5 mm0.4 mm (4 mesh to 35 mesh) range. It may sometimes be recommended also for finer grinding. Within these limits a rod mill is usually superior to and more efficient than a ball mill. The basic principle for rod grinding is reduction by line contact between rods extending the full length of the mill, resulting in selective grinding carried out on the largest particle sizes. This results in a minimum production of extreme fines or slimes and more effective grinding work as compared with a ball mill. One stage rod mill grinding is therefore suitable for preparation of feed to gravimetric ore dressing methods, certain flotation processes with slime problems and magnetic cobbing. Rod mills are frequently used as primary mills to produce suitable feed to the second grinding stage. Rod mills have usually a length/diameter ratio of at least 1.4.

Tube mills are in principle to be considered as ball mills, the basic difference being that the length/diameter ratio is greater (35). They are commonly used for surface cleaning or scrubbing action and fine grinding in open circuit.

In some cases it is suitable to use screened fractions of the material as grinding media. Such mills are usually called pebble mills, but the working principle is the same as for ball mills. As the power input is approximately directly proportional to the volume weight of the grinding media, the power input for pebble mills is correspondingly smaller than for a ball mill.

A dry process requires usually dry grinding. If the feed is wet and sticky, it is often necessary to lower the moisture content below 1 %. Grinding in front of wet processes can be done wet or dry. In dry grinding the energy consumption is higher, but the wear of linings and charge is less than for wet grinding, especially when treating highly abrasive and corrosive material. When comparing the economy of wet and dry grinding, the different costs for the entire process must be considered.

An increase in the mill speed will give a directly proportional increase in mill power but there seems to be a square proportional increase in the wear. Rod mills generally operate within the range of 6075 % of critical speed in order to avoid excessive wear and tangled rods. Ball and pebble mills are usually operated at 7085 % of critical speed. For dry grinding the speed is usually somewhat lower.

The mill lining can be made of rubber or different types of steel (manganese or Ni-hard) with liner types according to the customers requirements. For special applications we can also supply porcelain, basalt and other linings.

The mill power is approximately directly proportional to the charge volume within the normal range. When calculating a mill 40 % charge volume is generally used. In pebble and ball mills quite often charge volumes close to 50 % are used. In a pebble mill the pebble consumption ranges from 315 % and the charge has to be controlled automatically to maintain uniform power consumption.

In all cases the net energy consumption per ton (kWh/ton) must be known either from previous experience or laboratory tests before mill size can be determined. The required mill net power P kW ( = ton/hX kWh/ton) is obtained from

Trunnions of S.G. iron or steel castings with machined flange and bearing seat incl. device for dismantling the bearings. For smaller mills the heads and trunnions are sometimes made in grey cast iron.

The mills can be used either for dry or wet, rod or ball grinding. By using a separate attachment the discharge end can be changed so that the mills can be used for peripheral instead of overflow discharge.

grinding cylpebs

grinding cylpebs

Our automatic production line for the grinding cylpebs is the unique. With stable quality, high production efficiency, high hardness, wear-resistant, the volumetric hardness of the grinding cylpebs is between 60-63HRC,the breakage is less than 0.5%. The organization of the grinding cylpebs is compact, the hardness is constant from the inner to the surface. Now has extensively used in the cement industry, the wear rate is about 30g-60g per Ton cement.

Grinding Cylpebs are made from low-alloy chilled cast iron. The molten metal leaves the furnace at approximately 1500 C and is transferred to a continuous casting machine where the selected size Cylpebs are created; by changing the moulds the full range of cylindrical media can be manufactured via one simple process. The Cylpebs are demoulded while still red hot and placed in a cooling section for several hours to relieve internal stress. Solidification takes place in seconds and is formed from the external surface inward to the centre of the media. It has been claimed that this manufacturing process contributes to the cost effectiveness of the media, by being more efficient and requiring less energy than the conventional forging method.

Because of their cylindrical geometry, Cylpebs have greater surface area and higher bulk density compared with balls of similar mass and size. Cylpebs of equal diameter and length have 14.5% greater surface area than balls of the same mass, and 9% higher bulk density than steel balls, or 12% higher than cast balls. As a result, for a given charge volume, about 25% more grinding media surface area is available for size reduction when charged with Cylpebs, but the mill would also draw more power.

ball mill | ball mills | wet & dry grinding | dove

ball mill | ball mills | wet & dry grinding | dove

DOVE Ball Mills are supplied in a wide variety of capacities and specifications. DOVE small Ball Mills designed for laboratories ball milling process are supplied in 4 models, capacity range of (200g/h-1000 g/h). For small to large scale operations, DOVE Ball Mills are supplied in 17 models, capacity range of (0.3 TPH 80 TPH).

With over 50 years experience in Grinding Mill Machine fabrication, DOVE Ball Mills as critical component of DOVE Crushing plants are designed with highest quality of material for long life and minimum maintenance, to grind ores to 35 mesh or finer.

DOVE Grinding Mills are supplied in a wide range of capacities and specifications, for reliable and effective grinding, size reduction applications and for diverse applications of either dry or wet ore.

DOVE Ball Mills have extended history in the Mining and Mineral Processing Industry, Construction, Solid Waste Processing, Food Processing Industry, Chemical and Biochemical Industry, for Pyrotechnics and Ceramics.

DOVE Ball Mills are designed to operate with various types of grinding media, including Ball Mills Balls. DOVE supply Steel Balls in Various sizes and specifications. Cast Iron steel Balls, Forged grinding steel balls, High Chrome cast steel bars, with hardness of 60-68 HRC. We also supply Grinding Cylpebs with surface hard ness of 60-68 HRC, and grinding Rod with surface hardness of 55-60 HRC.

DOVE Ball Mills are made of high grade cast and carbon steel for extra strength, long and trouble-free operations. The inner lining plate designed with high manganese steel for long life and minimum wear off.

DOVE Ball Mill can be integrated in a Complete Plant designed by DOVE Engineering Services, provided for our Clients application and supplied with all components of the plant for efficient processing, smooth operation and efficient integration with the balance of the Processing Plant.

DOVE Ball mills, also known as Grinding mill, Mining mill, Pebble mill, Ball & Pebble mill, is an important machinery in the mining and various other industries, which would require grinding different material.

They are highly efficient Grinding mill machines, designed for grinding applications, where fine material is required. DOVE Ball Mills are used in supplied and applicable for wet and dry grinding applications within the following branches of industries:

DOVE ball mills is a rotating horizontal cylinder that tumbles the material to grind with a certain media. The standard media that we use in our ball milling process are the steel grinding balls, however depending on the specific application, we can configure the grinding mill with different media.

DOVE supplies various types and sizes of Ball Mill Balls, including; Cast Iron steel Balls, Forged grinding steel balls, High Chrome cast steel bars, with surface hardness of 60-68 HRC. DOVE Ball Mills achieves size reduction by impact and attrition. When the cylinder rotates, the balls are dragged to almost the top of the shell, and from there, they fall unto the material, which lead to the material breaking due to the impact.

DOVE Ball Mills are used in hard rock mineral processing plants as an ore-dressing step to grind the rocks into fine powder size, liberating the mineral particles from the rocks. This will ensure that the ore is well prepared for the next stage of processing and optimize the recovery of the minerals.

DOVE ball mill is integrated and used in DOVE Portable and Semi-Stationary Hard Rock plants (Hard Rock processing plants) to efficiently grind the ore from primary deposit until the liberation size of valuable minerals is reached. DOVE ball mill is the key grinding equipment after material is crushed. It is used to grind and blend bulk material into powder form using different sized balls. The working principle is simple, impact and attrition size reduction take place as the ball drops from near the top of the rotating hollow cylindrical shell of the Ball Mill. The output materials will be feed to the processing and recovery machines.

DOVE Ball Mills are deigned for either wet or dry grinding of materials, in various models, and in accordance to the processing and the crushing plant design, to cater to the liberation size of the minerals and the hardness of the ore.

DOVE supplies two different kinds of ball mills Grate type, and Overfall type. The difference between the two type is according to their ways of discharging material, and the plant flow design specifications.

The Grinding Balls will grind the material into powder size of 20 to 75 micron. In mining operations, this will allow for the liberation of gold and other precious metals that are hosted by the rocks. Many types of grinding media are suitable for use in a ball mill, each material having its own specific properties, specification and advantages.

Media Size: The grinding media particles should be substantially larger than the largest pieces of final material after grinding. The smaller the media particles, the smaller the particle size of the final product.

Composition: Each ball mill application has different requirements. Some of these requirements are relates to the grinding media being in the finished product, while others are based on how the media will react with the material being milled. Therefor, grinding media selection plays major factor on the final milled product.

Contamination: In certain grinding mill process, low contamination is important, the grinding media may be selected for ease of separation from the finished product, for example steel dust produced from steel balls can be magnetically separated from non-ferrous products. An alternative to separation is to use media of the same material as the product being milled.

Corrosive:Certain type of media, such as steel balls, may react with corrosive materials. For this reason, stainless steel balls, or ceramic balls, and flint grinding media may each be used when corrosive substances are present during grinding.

Related Equipments