technical specifiion of mineral flotation cell machine

continuous mechanical flotation cell | continuous mechanical flotation machine | continuous mechanical flotation separator - gtek

continuous mechanical flotation cell | continuous mechanical flotation machine | continuous mechanical flotation separator - gtek

FX Model Continuous Mechanical Flotation Machine is applicable to separation of minerals with float-free method in labs. It is a unit of several combinations of two cells with number of the cell being even, varying from two to ten cells. Left or right type flotation machine can be supplied as required by customer.

FX flotation machine is a kind of impeller mechanical flotation machine which mainly consist of cell. It is made of welded steel plate and through impeller agitation and scraping device.1. To adjust the level of slurry in the cell and the thickness of the scraped froth layer, use wall plates of the two cells to make intermediary cell; install slurry level regulator; and mount orifice plate onto the cover in the cell to avoid negative effects on the froth zone exerted by the chaotic motion of slurry, as well as to avoid the gangue from being taken into the concentrate by the machine.Lining plates are installed at the cell so that the bottom of the cell will not be abraded. The lining plate can be replaced. On the outside of the cell bottom is a discharge mouth, which is used to discharge water during its cleaning.The slurry flows through the overflow mouth of wall panel into the intermediary cell and tail cell. It flows to the lower part of the intermediary cell and the duct covered by the lower part of the cell wall and then to the next cell. In this way, it can continue to flow through all the cells of flotation machine. It flows from the feed cell and is discharged from the discharge mouth of the tail cell. The front and back of the lower part of the cell is installed feeding mouth, to make it easy to change the process flow.2. The impeller system is a disk impeller which is installed in the center of the cell in the flotation machine and whose blades are radially arranged. It is fixed onto the lower end of the impeller shaft and revolves around the vertical shaft pipe. The upper end of the pipe lies above the pulp stone and the froth layer while its lower end is supported on the cover. When the impeller rotates, a large amount of air can be sucked along the vertical pipe. Below the cover is fixed protective disk. The gap between the safety disk and the impeller depends on the amount of sucked air. It can not be larger than 3mm at most. When the gap is too large, replace the abraded protective disc and make appropriate adjustment.The holes in the vertical pipe are used to circulate slurry as well as mix the slurry and air. The rolling shaft installed inside the bearing shell above the impeller shaft rotates. The bearing shell is installed on the crossbeam and belt pulley is fixed on the top of the shaft which rotates through the V-belt when the motor is turned on. The tension of the V-belt is adjusted through the nuts.3. Scraping device: The froth is scraped along the flotation machine through rotary scraper. The scraper is installed outside the discharge mouth of cell. At one end of the scraping shaft is installed belt pulley which rotates through the drive of worm reducer and V-belt.

metso rcs flotation machines - metso outotec

metso rcs flotation machines - metso outotec

Optimal mineral recovery in a flotation circuit depends on the capacity to adapt to metallurgical variability in the ore being processed. Recognizing the need for a solution that addresses these challenges, Metso has made several advances in flotation design and technology.

Combining the benefits of circular cells with the unique features of the patented DV mechanism, the RCS (Reactor Cell System) flotation technology has been developed to create ideal conditions to maximize flotation performance for all roughing, cleaning and scavenging duties. The cell can be modified to handle high density slurries.

Maximize bubble-particle contact within the mechanism and the flotation tank leads to enhanced performance. Effective air dispersion and distribution throughout the cell volume helps in smooth froth surface and removal.

Our RCS flotation machines are built with efficient air and level controls with controlled aeration rate at each cell. The pneumatically operated dart valves help in effective pulp level control followed by accurate measurement with ultrasonic level sensor and float.

Metso offers the innovative circular tank concept to minimize slurry short circuiting as well as simplifying froth handling process. The compact and modular design proves to be very beneficial for quick construction, shipment and installation. Our internal dart valves also help to minimize footprint requirements.

Metso RCS flotation machines have extended wear life due to minimized local high velocity zones inside the tank. Impellers and diffusors supplied in high abrasion-resistant elastomers, and the impeller profile is design to minimize adsorbed power.

The mechanism design produces powerful radial slurry pumping to the cell wall and gives strong return flows to the underside of the impeller to minimize sanding. Additionally, it is the only mechanism to give maximum slurry recirculation to the upper part of the impeller.

The modular dart valve design provides flexibility to capacity changes without disturbances.Full suspension of the DV mechanism from the cell superstructure leads to very simplified routine maintenance. Along with our robust design, the RCS flotation machines are built to work for you!

Metso RCS flotation machines also are found as an essential piece to a regrind circuit. Rougher cells extract majority of the valuable mineral from the fresh ore. Meanwhile, scavenger cells are going to capture the remaining valuable mineral.

Revolutionary image analysis system for live measurement of multiple froth properties such as velocity, color, bubble size distribution, texture, stability and more. Higher froth recovery with continuous monitoring and analysis of flotation cells.

continuous mechanical flotation cell - gtek laboratory

continuous mechanical flotation cell - gtek laboratory

FX Model Continuous Mechanical Flotation Machine is applicable to separation of minerals with Float-free method in labs. It is a unit of several combinations of two cells with number of the cell being even, varying from two to ten cells. Left or right type flotation machine can be supplied as required by customer.

FX flotation machine is a kind of impeller mechanical flotation machine which mainly consist of cell. It is made of welded steel plate and through impeller agitation and scraping device.1. To adjust the level of slurry in the cell and the thickness of the scraped froth layer, use wall plates of the two cells to make intermediary cell; install slurry level regulator; and mount orifice plate onto the cover in the cell to avoid negative effects on the froth zone exerted by the chaotic motion of slurry, as well as to avoid the gangue from being taken into the concentrate by the machine. Lining plates are installed at the cell so that the bottom of the cell will not be abraded. The lining plate can be replaced. On the outside of the cell bottom is a discharge mouth, which is used to discharge water during its cleaning. The slurry flows through the overflow mouth of wall panel into the intermediary cell and tail cell. It flows to the lower part of the intermediary cell and the duct covered by the lower part of the cell wall and then to the next cell. In this way, it can continue to flow through all the cells of flotation machine. It flows from the feed cell and is discharged from the discharge mouth of the tail cell. The front and back of the lower part of the cell is installed feeding mouth, to make it easy to change the process flow.2. The impeller system is a disk impeller which is installed in the center of the cell in the flotation machine and whose blades are radially arranged. It is fixed onto the lower end of the impeller shaft and revolves around the vertical shaft pipe. The upper end of the pipe lies above the pulp stone and the froth layer while its lower end is supported on the cover. When the impeller rotates, a large amount of air can be sucked along the vertical pipe. Below the cover is fixed protective disk. The gap between the safety disk and the impeller depends on the amount of sucked air. It cannot be larger than 3mm at most. When the gap is too large, replace the abraded protective disc and make appropriate adjustment.The holes in the vertical pipe are used to circulate slurry as well as mix the slurry and air. The rolling shaft installed inside the bearing shell above the impeller shaft rotates. The bearing shell is installed on the crossbeam and belt pulley is fixed on the top of the shaft which rotates through the V-belt when the motor is turned on. The tension of the V-belt is adjusted through the nuts.3. Scraping device: The froth is scraped along the flotation machine through rotary scraper. The scraper is installed outside the discharge mouth of cell. At one end of the scraping shaft is installed belt pulley which rotates through the drive of worm reducer and V-belt.

laboratory flotation cell | lab single flotation cell | lab flotation machine | lab flotation separator | lab ore flotation equipment | xfd single flotation cell | xfd2 single flotation cell - gtek

laboratory flotation cell | lab single flotation cell | lab flotation machine | lab flotation separator | lab ore flotation equipment | xfd single flotation cell | xfd2 single flotation cell - gtek

This flotation cell can be used for mixing, separation, cleaning, mineral sample concentration in the laboratory room of mineral processing plant, universities and research institutions, and also in geology, metallurgy, construction, chemistry, and coal industry.

1. Converter technology, stepless speed adjustment of impeller and with LCD digital display2. Easy and accurate adjustment, reliable operation3. Liquid level and air filling volume adjustable, with speed digital display device and water make-up device

flotation cells | prominer (shanghai) mining technology co.,ltd

flotation cells | prominer (shanghai) mining technology co.,ltd

Prominer can provide SF series self-priming flotation machine and XCF/KYF series pneumatic flotation cell which are mainly used. for the recovery and upgrading of sulfide ores such as cooper ore, lead & zinc ore, gold ore, silver ore, nickel ore. And it can be also used in some non-sulfide ores include fluorite, graphite, quartz, tungsten, lithium, tantalum, tin and coal.

For ensuring the performance our flotation system, the suitable chemical reagent system also very important. Based on the function of chemical reagent, it can be classified as collectors, frothers and modifiers.

Prominer has been devoted to mineral processing industry for decades and specializes in mineral upgrading and deep processing. With expertise in the fields of mineral project development, mining, test study, engineering, technological processing.

pilot flotation plant - crushers, ball mills and flotation cells for mining and mineral beneficiation

pilot flotation plant - crushers, ball mills and flotation cells for mining and mineral beneficiation

Pilot Flotation Plant (Capacity 3-5 kg/h) is applied in test of continuous flotation of minor representative ore samples with its test result being able to represent the results of lab and pilot plant tests, and supply available mineral beneficiation indexes for lab and pilot plant in short time.

1. Application Pilot Flotation Plant (Capacity 3-5 kg/h) is applied in test of continuous flotation of small amount of ore samples with its test result being able to represent the results of lab and pilot plant tests, and supply available mineral beneficiation indexes for lab and pilot plant in short time.

Pilot Flotation Cell Plant is self-suction agitated continuous flotation machine with no need or need of small amount of auxiliary equipment, and convenient configured equipment adjustable for easy finish the job of mineral processing tests on non-ferrous, ferrous and non-metallic minerals.

Pilot Flotation Plant are mainly composed of slurry storage drum 1, agitating drum 2, micro reagent feeding machine 1, squeegee pump 2, and continuous flotation machines of 1 liter 8 cells, 0.75 liter 4 cells, and 0.5 liter 2 cells.

The agitating Tank is agitated through the rotation of wheels to keep the slurry even. The slurry flows to the agitating dram and flotation machine from the slurry storage drum. The change of its flow is realized through the change of flow area.

Such continuous flotation machine has characteristics such as strong suction capacity and large aeration quantity. The flow of slurry and froth products and suction of air are realized through the rotation of impeller. In case of middling return caused by negative pressure, squeegee pump can be added according to actual conditions. Extension tube is needed for the adjustment of liquid level. Change the length of extension tube and the height of liquid level can be adjusted. It is easy to make adjustment without any blockage.

We could design and produce Pilot Flotation Plant according to your demands. Please tell your requirements: capacity, raw material, feeding size, ore pulp density, then we will design the flotation plant for you.

ZJH mainly focus on producing and supply crushers, ore grinding equipment, mineral Beneficiation equipment, laboratory and pilot scale ore dressing equipment for Mining and Mineral Processing Industry. Our aim is to work together with Mines, Mineral Beneficiation Plantsfor helping to reduce the operating cost ,to improve the operating efficiency.

Related Equipments