toothed roll crusher holder

toothed roll crusher for coal preparation plant - ftm machinery

toothed roll crusher for coal preparation plant - ftm machinery

Toothed roll crusher is widely used in coal, metallurgy, mining, chemical industry, building materials, and other industries, and it is more suitable to crush coal in large coal preparation plant and process waste. Toothed roll crusher has a high crushing capacity. The distance between the rollers can be adjusted by hydraulic pressure. The bearing of the toothed roll crusher is centralization lubrication. Whats more, it has the advantages of optimal design, high efficiency, uniform grain, and low cost.

Protective device: The motor is connected with the retarder through hydraulic coupling to avoid dynamic overload. The sensor overload protection is very reliable. If you have mining project or chemical plant, the toothed roller crusher is prepared for you in China Fote.

The toothed roll crusher is suitable for crushing raw coal in coal mines, coal preparation plants and other industries (allowing less than 30% of coal gangue in raw coal). The crusher is also used to break other brittle materials whose hardness is similar to that of raw coal.

It has the characteristics of high efficiency, long life, full sealing, low noise, and uniform granularity. The double-toothed roll crusher is equipped with a scraper to keep the groove and working surface clean. For the toothed roll crusher, the outlet-size depends on the gap between the two rollers, the size of teeth, shape of teeth, and the number.

The double-toothed roll crusher is relatively small in volume. It consists of two tooth rolls that are mounted in parallel and rotate in opposite directions. According to the crushing capacity and the size of the discharging granularity, the two crushing rolls are uniformly filled with brushing teeth.

And the double-toothed roll crusher adopts the operation way of non-circular, non-intermesh and non-uniform, which can enhance the contact face of roller teeth, and avoid material slippage and improve crushing efficiency.

When the toothed roller rotates, the teeth on the surface of the roller can bite the materials and crush them. Each roller crusher of the crushing system is driven by a separate motor. The roller crusher is generally driven by a belt, and it constitutes the deceleration system along with the reducing mechanism.

FTM double-tooth roller crusher for sand making, limestone, rock, clay crushing has a good crushing effect on wet and sticky materials. And adherence or clogging phenomenon never occurs during the work.

The silicon-aluminum raw material is an indispensable calibration material in the dry cement production process. After the mining work, the materials need to be crushed, transported and stored. and then they are sent to the raw material mill for grinding according to an appropriate ratio.

However, the silico-alumina raw materials have strong water storage capacity and high plasticity index, especially for bauxite and marlstone with water content more than 17% and plasticity index generally above 15. Because of the viscosity of materials, it can lead to blockage and arching during the process of crushing, transportation and storage, thus affecting the normal operation of the system.

In order to solve the problem of adherence and clogging of wet-adhesive materials in the crushing stage, FTM toothed roll crusher is used to break the mixture of limestone and marl. In detail, firstly, the wet and dry materials are mixed and crushed, and secondly, the wet-adhesive materials and other limestone materials with lower moisture content are mixed into the crusher. And finally, they are crushed according to an appropriate ratio.

The toothed roller crusher machine has advantages of small volume, large crushing ratio, low noise, simple structure, convenient maintenance, high productivity, uniform particle size of crushed material, low crushing rate, convenient maintenance, sensitive overload protection, safe and reliable.

china ac motor roll crusher, ac motor roll crusher manufacturers, suppliers, price

china ac motor roll crusher, ac motor roll crusher manufacturers, suppliers, price

China manufacturing industries are full of strong and consistent exporters. We are here to bring together China factories that supply manufacturing systems and machinery that are used by processing industries including but not limited to: roller crusher, mining machine, mining equipment. Here we are going to show you some of the process equipments for sale that featured by our reliable suppliers and manufacturers, such as AC Motor Roll Crusher. We will do everything we can just to keep every buyer updated with this highly competitive industry & factory and its latest trends. Whether you are for group or individual sourcing, we will provide you with the latest technology and the comprehensive data of Chinese suppliers like AC Motor Roll Crusher factory list to enhance your sourcing performance in the business line of manufacturing & processing machinery.

double roll & teethed roll crusher

double roll & teethed roll crusher

Although its brief period of popularity passed some thirty-odd years since, and only a few sets were installed before interest reverted to other types, the high-speed double roll crusher developed by Thomas A. Edison shortly before the end of the last century warrants a place in any discussion-of crushing equipment. In 1960, the largest machine of this type the 6 x 7 foot giant rolls were huge crushers, judged even by present-day standards; they have an unobstructed receiving opening 7 x 7 foot and their capacity on individual skip-loads of stone is enormous, although, as will be explained, they cannot maintain this peak capacity over a period of time.

Mechanically, the teethed roll crusher is a very simple machine. The two rolls are carried in bearings, supported on two very heavy and rigid bed castings which are secured on the concrete foundation by a number of large anchor bolts. The bearings, in addition to being bolted to these bed castings, are prevented from spreading by pairs of large tie-rods which pass through them above and below the roll shafts. Unlike the smooth-face crushing rolls we have described, these tension rods are not cushioned by springs. The machine is surmounted by a heavy cast rectangular hopper, all sides of which are vertical. Each roll is independently driven by a flat-belt pulley.

The roll-centres are octagonal in cross section, each face being provided with a spline groove and a series of tapped holes for securing the chilled- iron wearing plates. These wearing plates have the sledging knobs, or teeth, cast on their outer surfaces. Thus we have a roll surface that resembles that of the one rollcrusher, except that the faces of all teeth are sloped instead of radial on the advance side. The usual practice is to fit one roll entirely with so-called regular teeth, and the other roll with six rows of regulars and two rows of higher (slugger) teeth.

The peripheral speed, or tip-velocity, of these rolls is much higher than that of any of the machines we have previously described. The range of the smooth-face rolls, for example, is from about 400 ft/min for the small 12-in. rolls, to 2000-2200 feet/minute for the heavy-duty 72 machine. The single-roll crusher has a tip speed of 400-450 ft/min while the 6- x 7-ft teethed roll crusherhas a normal, no-load, surfaces speed of just under 3500 ft/min. It can be readily appreciated that this high velocity induces an extremely violent crushing action, in conjunction with the 3- to 4-in. knobs which protrude from the roll surfaces. Impact, sledging, and pressure crushing enter into the over-all performance; but impact, in this crusher, plays a far more important role than it does in the slower speed single-roll machine; and crushing, even well down along the roll faces, is more in the nature of a sledging action than it is of pressure crushing, for this action occurs in the lower-velocity crushers.

The theoretical maximum size of cube that the knobs will grip, when the rolls are set at minimum spacing, is 24; but the rolls will reduce any stone that can be introduced into the 7-ft square hopper. Large blocks will span across the tops of the two rolls; immediately the slugger teeth on the one roll so equipped go to work on these blocks and quickly shatter them into pieces that can be gripped between the sets of regular teeth; from this point on, the action is a mixture of sledging and pressure crushing. The same selective segregations which we described in connection with the single-roll machine occur in the double-roll crusher; the smaller pieces are cleared quickly, leaving the roils free to work on the larger blocks.

The entire performance on individual skip-loads of stone takes place in a very short period of time. Ten- ton loads of mixed-size medium limestone will clear the crusher in from 10 to 15 sec.; large single blocks, weighing from 6 to 8 tons, are crushed in from 5 to 20 seconds, depending upon the toughness of the individual piece, and upon the way it happens to land in the crushing chamber. These performances were clocked on ma-chines turning out a 6 product.

The short-time transfer of energy, especially when crushing large blocks, is very high; so high in fact that it would not be economically feasible to provide sufficient motive power to deliver it. The usual practice, when these rolls are driven electrically, is to drive the slugger roll with a 250 HP motor, and the regular roll with 200HP,a total of 450 HP. As compared to this motive power, instantaneous energy delivery may run as high as 4000 HP, obviously far beyond the capacity of the motive equipment. But the rolls themselves, when running at normal no-load speed, have a stored kinetic energy of upwards of 4,000,000 ft -lb , and it is this stored energy that does much of the actual crushing, the motors serving to bring the rolls back to normal speed between crushing periods. In crushing a skip-load of stone the rolls may lose anywhere from 30 to 60 RPMin speed; this loss occurs partly through slowing down of the motive equipment, and partly through belt slippage. It requires from 5 to 10 sec. to bring the machine back to speed, during which time the power input will vary from 400 to 600 HP. The power required to run the rolls empty is something less than 100 hp. The average power consumption, when crushing from 3000 to 4000 tons per 10 hour day will run in the neighbourhood of 150 HP on medium limestone.

While the average power consumption of this machine compares favorably with that of other types, the rather violent fluctuation outlined and the relatively high connected horsepower are unfavourable features. It is also natural to expect that the belt slippage we have noted would constitute something of a problem over a period of time. Performance records indicate that belt trouble accounts for about 50% of the total lost time on a set of these rolls, and about 25% of the total maintenance expense.

The type of quarry equipment most commonly used in conjunction with this crusher is the three-sided steel skip, carried on a flat-top truck or flat car. These skips are provided with a shackle on the rear end, which is engaged by a hook actuated by a small hoist. This apparatus slides the skip over against the lip of the receiving hopper, and tilts it to discharge its contents. The skips discharge over a feed-roll which retards the flow of material so that the entire load does not drop into the crushing chamber at once. When the skip is empty it is pulled back on to the truck or car by a counterweight attached to the opposite end of the same cable which performs the hoisting operation.

We have mentioned the heavily ribbed hopper which surmounts the frame and extends up to the level of the feed roll. This hopper serves the double purpose of directing the material into the crushing zone, and preventing stones thrown by the slugger teeth from flying out of the crusher. It is also necessary to cover the top of the hopper with heavy netting to contain flying spalls.The straight-sided, rectangular hopper construction, and the violent agitation in the crushing chamber, tend to minimize blocking and bridging in this crusher. When bridges do occur they are difficult and dangerous to break while the rolls are running.

Practically all that we have had to say about the application of the single-roll crusher will apply as well to the Edison toothed roll crusher. It is better adapted to handling blocky stone than is the single-roll machine, because itsslugging action is much more vigorous, and it will handle any material that will not build up on the sides of the vertical hopper. It is not as simple a machine to feed as the single roll crusher, because its narrow hopper necessitates the uses of skips, or very short-bodied cars. A heavy- duty apron feeder would of course solve this problem, but so far as we know, none of these crushers were so equipped. The high peak capacity of the crusher constitutes something of a problem in plants of medium capacity. It is not economically feasible to provide elevating or conveying equipment to handle peak loads of around 4000 TPH in a plant designed to turn out that much stone in an 8 or 10 hr day; consequently means must be provided to smooth out these high surge loads. This can be taken care of by a surge bin and feeder below the crusher, or by passing the roll product direct to a secondary crusher of uniform-capacity characteristic. A feeder ahead of the rolls would smooth out peaks on mixed feed but. once a 10 or 12 ton block of stone is dropped into the crusher, that quantity comes through very quickly as crushed stone, which would render the regulating properties of the feeder of questionable value.Modified forms of this crusher were used by Edison for secondary and tertiary stages. The crushing equipment in one large plant, for example, comprised a set of 6- x 7-ft rolls (8 product), a set of 4 x 4 feet secondary rolls (3.5 product), and a set of 4 x 3 ft tertiary rolls (1.5 product), these last rolls being in closed circuit. These smaller machines were also run at high speeds, their surface velocities being slightly over 3000 ft/min.

coal crushing: new-type toothed roll crusher vs traditional toothed roll crusher | hxjq

coal crushing: new-type toothed roll crusher vs traditional toothed roll crusher | hxjq

In the coal industry, the requirements for the particle size of the finished product are extremely strict. Generally, the particle sizes of the finished products are between 25 and 70 mm. If it is too large, the furnace will be blocked and further coal processing can't be performed.

Toothed roll crusher is the mature coal crushing equipment applied in the current coal industry, which satisfies all the demands of customers by its advantages of large capacity and low over-crushing rate.

Based on the original toothed roll crushers, HXJQ Mining Machinery has optimized the structure and materials of rollers according to the customers' requirements, so that to adapt the nature of hard gangue and special working conditions and ensure the normal production of coal enterprises.

Traditional toothed roll crusher is usually driven by double-motors. Two sets of motors, couplers and reducers are adopted to drive the independent rollers so that the rollers have the power to crush large coal materials.

The coupler is applied between reducer and rolls to transfer torque. And the toothed rollers and drive system are connected with the machine frame respectively to eliminate the vibrating of toothed roll crusher.

Traditional toothed roll crusher with ring structure has the advantages of stable and reliable performance, and the disadvantages of low wear resistance and hard to replace. Once the traditional toothed roll crusher is damaged, it must be returned to the factory for overhaul.

The traditional rollers are connected by the bolts and tooth-holders, which offers small bearing capacity. Therefore, the traditional toothed roll crushers are mainly applied in the clean-coal crushing process, because the raw coal will cause damage to roll crusher teeth.

In terms of tooth position, the roll crusher teeth are set in the peripheral direction, adopting the setting form of large tooth alternating with a small one. Under the premise of normal discharging size, the crushing force of roller can be improved efficiently, so that to increase the capacity, wear-resistance and service life.

As the picture shows, the new-type tooth-holder adopts the form of regular octagon. The toothed rollers and toothed holders are connected by the flat kay and socket head cap screws (the traditional ones are connected by bolts).

The contacted areas between tooth and toothed holders are processed and improved completely, and torque is transferred by flat key so that can prevent the socket head cap screws from the shearing force of coal materials. And the screws can be firmer and more reliable.

Meanwhile, the fastening bolt and the toothed roller holder are connected by the screw fastening blocks, which makes that the joint strength is ensured, and the interchangeability and the replaceability are also reliable.

The teeth are the main wearing parts of the toothed roll crusher, so it is very necessary to choose a suitable material. Therefore, it is required that the material should have enough hardness, toughness, impact resistance and wear resistance. Also, the following machinability and weldability should be considered.

When parts of high manganese steel are impacted repeatedly, the surface of parts gets changed, and the hardness increases rapidly, which can reach up to HRC54. It will improve the wear resistance significantly, but the inside of parts keeps flexibly. These are the main features of high manganese steel.

However, the toothed roll crushers crush coal materials by shearing and stretching, along with less impacting and squeezing, which makes high manganese steel can't play its advantages to enhance the hardness and strength. Therefore, high manganese steel is not suitable for making teeth.

To better improve the wear-resisting performance of teeth, traditional toothed roll crusher always adopts the low-alloy quenched and tempered steel as the material to make tooth of roll crushers. In general, 40 Cr is used to process the tooth. After processing, the compressive strength and the service life of tooth are improved.

However, since there are only a few millimeters thick wear-resisting layer in the surface of the tooth, it is required to be overlaid frequently in the process of use, which brings a large workload to workers.

The teeth of the new toothed roll crusher adopt the integral casting molding process, optimizes the proportion of the main elements such as C, Cr, Mn, Mo, Si, Ni. The medium carbon bainitic steel is selected finally to be the material of toothed roll.

The medium carbon bainitic steel has good hardenability. After quenching and tempering heat treatment, bainite with high hardness and wear resistance is processed. It has an excellent comprehensive performance of HRC50 hardness and compressive strength of 1500 MPa.

In addition, the material of the entire toothed roller structure, including the toothed roller, the toothed roller holder and the threaded fastening block, is reasonably matched, so that the strength and hardness of each component are more balanced and reasonable.

The raw coal is first crushed to below 300mm by the jaw crusher, and then crushed to below 70mm by a toothed roller crusher, and then transported to the coal storage bin by the belt conveyor. After screening, the final product of 25~70mm is sold to the chemical company.

The customer said it requires technical improvement urgently in their worksite urgently to reduce the operating cost of the enterprise and the labor intensity of the workers and to ensure the normal operation of the production system.

Since the new toothed roller crusher was put into use, the equipment has been running stably, the discharge size of the products is significantly improved, the over-crushing rate reduces, and the block-forming rate is highly increased (see the following table).

It can be seen from the above table that the difference between the qualified products before and after the replacement is 18.2%, which greatly improves the output of qualified products and creates great economic benefits for the enterprise.

In addition, the new toothed roller crusher has high wear resistance, and the fastening bolt is not easy to loosen, which reduces a large amount of maintenance time, the labor intensity of workers, and the maintenance cost of the coal crushing process.

With the transformation and upgrading of the coal industry, it is an inevitable trend to vigorously develop coal chemical industry. The coal chemical industry has strict requirements on the particle size of coal, which puts higher requirements on the crushing equipment.

The new toothed roller crusher can optimize the crushing operation of the raw coal by a series of optimizations on the structure and material of the toothed roller. It has a high block rate and a small maintenance amount. With the obvious technical advantages, the promotion prospects of new-type toothed roll crusher are broad.

Related Equipments