wear parts of ball mill table

cement mills and raw mills for high throughput rates

cement mills and raw mills for high throughput rates

High throughput rates, permanent plant availability , optimized maintenance concepts features of the MVR mill and the patented MultiDrive enabling Gebr. Pfeiffer to meet the ever rising expectations of the industry. Thanks to the innovative drive and active redundancy, an unintended stop of the grinding process is practically excluded. No matter what type of material has to be ground cement raw material, cement clinker or granulated blast-furnace slag and how different their grindability and abrasiveness may be, the MVR mill ensures throughput rates of a different dimension, around the clock, reliably and on the long term. Forget about downtime. With Pfeiffer you will grind on a grand scale.

An MVR mill may have up to six grinding rollers and up to six drive units. Thus both systems are actively redundant meaning that one or several rollers can be taken out of the system for maintenance work while mill operation continues. The same applies to the independent drive modules of the MultiDrive.

High drying capacity, short dwell time of the material to be ground, and remote control of grinding pressure and classifier rotor speed ensure a fully automatic operation of the MVR mill even with varying raw material characteristics.

Thanks to the geometry of the grinding rollers in combination with their specific suspension, there is always a parallel grinding gap, ensuring a homogeneous compaction of the material to be ground. Moreover, due to the symmetric shape of the grinding roller tires, these can be turned when worn.

Up to six stationary grinding rollers roll on a rotating grinding table. The material is drawn in between the rollers and grinding table and ground by pressure and shear. The required pressure forces are produced by a lever system comprising, among others, a roller arm, along with a hydropneumatic tension system. After being rolled over by the rollers, the material is conveyed to a stationary nozzle ring due to the rotation of the grinding table. Gases (air or hot gas) flow through this nozzle ring, take up the ground and dried material and convey it to the classifier where it is separated by the rotating wheel (rotor) into grits and fines. The grits fall back into the grinding zone whereas the fines leave the classifier with the gas flow for being separated in cyclones or a filter.

Up to six stationary grinding rollers roll on a rotating grinding table. The material is drawn in between the rollers and grinding table and ground by pressure and shear. The required pressure forces are produced by a lever system comprising, among others, a roller arm, along with a hydropneumatic tension system. After being rolled over by the rollers, the material is conveyed to a stationary nozzle ring due to the rotation of the grinding table. Gases (air or hot gas) flow through this nozzle ring, take up the ground and dried material and convey it to the classifier where it is separated by the rotating wheel (rotor) into grits and fines. The grits fall back into the grinding zone whereas the fines leave the classifier with the gas flow for being separated in cyclones or a filter.

Depending on the abrasiveness of the material to be ground and areas to be protected, different wear materials are used on our vertical roller mills. Alloy cast iron as per DIN 1695, hardfaced cast iron or composite materials with high-chromium inserts in ductile base materials: the grinding elements designed by Pfeiffer are made of high-quality materials ensuring a long lifetime. The housings and other mill components, too, are protected against wear with highly wear-resistant steel plates or hardfaced composite plates. Components which are specifically exposed to wear like gas outlet ducts have additional ceramic liners. All this is for optimum protection and short maintenance shutdown.

The highest wear occurs on the wear parts of the grinding elements as is the case with any type of vertical mill. Therefore, ease of replacement and regeneration is a major feature of the mill. The MVR mill has a modern hydraulic system used in operation and for maintenance alike. With this new type of roller suspension, the rollers can be swung out of the mill in a controlled way for ease of replacing the one-part grinding roller tires. The segmented wear parts of the grinding table are replaced, using a lifting device and the maintenance drive. Moreover, the rollers can be swung out separately. Hence grinding operation can be continued while maintenance work is done. The parts concerned can be regenerated both inside the mill and outside. Forget about downtime and maintenance problems! With active redundancy and easy maintenance you are up to date!

coal mill, gypsum mill, clay mill, etc. | pfeiffer mps mills

coal mill, gypsum mill, clay mill, etc. | pfeiffer mps mills

Highest flexibility with constant product quality, individually conceived, suitable for a variety of applications, undergoing constant development: with a number of more than 2800 mills sold, the MPS vertical mill is our proven allrounder. It can be used for the grinding of coal, petcoke, clay, limestone, quicklime and many other materials no matter how different their grindability and abrasiveness may be or whatever fineness or drying degree is required. The MPS mill also grinds, dries, calcines, and classifies gypsum without any problem, all in a single machine, for any fineness requested and considering individual requirements. The MPS vertical roller mill - built to last, reliable and energy-efficient - is the optimum solution when it comes to performing several process steps in one unit.

High drying capacity, short dwell time of the material to be ground, and remote control of grinding pressure and classifier rotor speed ensure a fully automatic operation of the MPS mill even with varying raw material characteristics.

Three stationary grinding rollers roll on a rotating grinding table. The material is drawn in between the rollers and grinding table and ground by pressure and shear. The required pressure forces are produced by a hydropneumatic tension system. After being rolled over by the rollers, the material is conveyed to a stationary nozzle ring due to the rotation of the grinding table. Gases (air or hot gas) flow through this nozzle ring, take up the ground and dried material and convey it to the classifier where it is separated by the rotating wheel (rotor) into grits and fines. The grits fall back into the grinding zone whereas the fines leave the classifier with the gas flow for being separated in cyclones or a filter.

Three stationary grinding rollers roll on a rotating grinding table. The material is drawn in between the rollers and grinding table and ground by pressure and shear. The required pressure forces are produced by a hydropneumatic tension system. After being rolled over by the rollers, the material is conveyed to a stationary nozzle ring due to the rotation of the grinding table. Gases (air or hot gas) flow through this nozzle ring, take up the ground and dried material and convey it to the classifier where it is separated by the rotating wheel (rotor) into grits and fines. The grits fall back into the grinding zone whereas the fines leave the classifier with the gas flow for being separated in cyclones or a filter.

Three stationary grinding rollers roll on a rotating grinding table. The material is drawn in between the rollers and grinding table and ground by pressure and shear. The required pressure forces are produced by a hydropneumatic tension system. After being rolled over by the rollers, the material is conveyed to a stationary nozzle ring due to the rotation of the grinding table. Gases (air or hot gas) flow through this nozzle ring, take up the ground and dried material and convey it to the classifier where it is separated by the rotating wheel (rotor) into grits and fines. The grits fall back into the grinding zone whereas the fines leave the classifier with the gas flow for being separated in cyclones or a filter.

Three stationary grinding rollers roll on a rotating grinding table. The material is drawn in between the rollers and grinding table and ground by pressure and shear. The required pressure forces are produced by a hydropneumatic tension system. After being rolled over by the rollers, the material is conveyed to a stationary nozzle ring due to the rotation of the grinding table. Gases (air or hot gas) flow through this nozzle ring, take up the ground and dried material and convey it to the classifier where it is separated by the rotating wheel (rotor) into grits and fines. The grits fall back into the grinding zone whereas the fines leave the classifier with the gas flow for being separated in cyclones or a filter.

Three stationary grinding rollers roll on a rotating grinding table. The material is drawn in between the rollers and grinding table and ground by pressure and shear. The required pressure forces are produced by a hydropneumatic tension system. After being rolled over by the rollers, the material is conveyed to a stationary nozzle ring due to the rotation of the grinding table. Gases (air or hot gas) flow through this nozzle ring, take up the ground and dried material and convey it to the classifier where it is separated by the rotating wheel (rotor) into grits and fines. The grits fall back into the grinding zone whereas the fines leave the classifier with the gas flow for being separated in cyclones or a filter.

Three stationary grinding rollers roll on a rotating grinding table. The material is drawn in between the rollers and grinding table and ground by pressure and shear. The required pressure forces are produced by a hydropneumatic tension system. After being rolled over by the rollers, the material is conveyed to a stationary nozzle ring due to the rotation of the grinding table. Gases (air or hot gas) flow through this nozzle ring, take up the ground and dried material and convey it to the classifier where it is separated by the rotating wheel (rotor) into grits and fines. The grits fall back into the grinding zone whereas the fines leave the classifier with the gas flow for being separated in cyclones or a filter.

Depending on the abrasiveness of the material to be ground and areas to be protected, different wear materials are used on our vertical roller mills. The grinding elements are primarily made of alloy cast iron as per DIN 1695, hardfaced cast iron or composite materials with high-chromium inserts in ductile base materials. The housings and other mill components are protected against jet wear with highly wear-resistant steel plates or hardfaced composite plates. Components which are specifically exposed to wear like gas outletducts have additional ceramic liners. All this is for optimum protection and short maintenance shutdown.

The highest wear occurs on the wear parts of the grinding elements as is the case with any type of vertical mill. Therefore, ease of replacement and regeneration is a major feature of the mill. With our proven Lift-and-Swing System, wear parts can be replaced rapidly through one single maintenance door. The grinding rollers and grinding table segments are driven to the maintenance door with the maintenance drive and are swung out of the grinding area. As a result maintenance downtime is reduced and work is easy and safe.

high chromium cast iron vertival roller mill spare parts grinding roller tire,table liner

high chromium cast iron vertival roller mill spare parts grinding roller tire,table liner

Production Description We manufacture different wear and impact resistant parts for yourvertical mill, for example: roller tire, segmented rollers, table liners and nozzle rings. Beside suitable material selection we offer hard weld deposit and other special applications to increase the surface hardness. High-chromium wear-resistant roll sleeves are widely used in large-scale materials such as metallurgy, electric power, cement, chemical, ceramics, non-metallic minerals, power plant desulfurization, water slag, slag, slag, coal, cement clinker, glass, quartz, limestone and other industries. Grinding and ultra-fine grinding. Rollers and Table Segments: Both are cast in High Chrome Alloys in the range of 16% to 27 % with a 55-62 HRC hardness. The use of High Chrome increases the wear life versus low and medium chrome alloys. Grinding roller is core part of vertical mill. Wecan provide customized service according to customers'different processing requirements. Besides, it provides finished product manufacturing service for grinding roller including casting, finished machining, surfacing welding, etc. We gained good reputation from customers. Application Area Vertical Mill/Cement Vertical Mill/Coal Vertical Mill/Raw Vertical Mill/Slag Vertical Mill/ Clinker vertical mill/ GGBSvertical mill We Supply... We supply replacement wear parts such as tires, grinding ring segments, armor rings and spindle shields are cast from our high chromium alloy irons and fully heat-treated for optimum mechanical properties. Tires and grinding ring segments are also accurately machined to tight tolerances for a precise fit. Parts requiring drilled or tapped holes such as roller bosses, clamping rings and dam ring segments are made of carbon steel or high strength steel. They are heat-treated to provide the best combination of hardness and toughness for long, trouble-free service. Our product engineers are responsive to customer requests for product improvement. As a vertically integrated plant, we can easily deal with the changes in design, metallurgy, heat treatment and machining. We offer customized services. You can send us your drawingsof your vertical mill wear parts in the case that we have not had developed your mill parts in the past. WhatsApp Us: 0086

crusher wear parts - me elecmetal global presence and distribution

crusher wear parts - me elecmetal global presence and distribution

ME Elecmetal is the leader in offering wear solutions to crusher operators. We provide wear parts for primary, secondary and tertiary crushing applications for the mining and aggregate industries with optimal designs and alloys specifically developed for each application.

ME Elecmetal is the leading global supplier for total wear product solutions in the mineral processing, aggregate, construction and recycle industries. ME Elecmetal produces the best crusher liners using the optimal blend of ultra-alloys and never taking shortcuts in the heat-treat and quenching process. Wear components for crushing processes are subjected to severe impact and high abrasion, requiring components made from impact- and abrasion-resistant alloys. We increase crusher availability through: Top-quality wear materials resulting in increased wear life Ideal crushing profiles through optimized liner designs Less on-going wear part maintenance Designs and tools for safe and efficient concave change out

ball mill liner function | wear parts for industry | qiming casting

ball mill liner function | wear parts for industry | qiming casting

Ball mill is a major equipment in the production of power plants, cement plants, mines, chemical industry, metallurgy and other industries, the liner is one of the components of the mill, the main role is to protect the cylinder, the cylinder from the grinding body and Material direct impact and friction, help to improve the mill grinding efficiency, increase production and reduce metal consumption. As the liner in the harsh conditions of long-term conditions, maintenance and replacement of considerable volume, not only requires human, material and financial resources, but also a direct impact on productivity.

Ball mill liner plays a major role in protecting the inner wall of the anchor windlass. Different shapes of the ball mill lining plate can improve the grinding effect of the ball mill and improve the working efficiency of the ball mill. 1, flat ball mill liner, the surface smooth, suitable for installation in the fine grinding warehouse. 2, the pressure of the type of ball mill liner, suitable for coarse grinding warehouse, for low speed ball mill. 3, ladder-type ball mill liner, ladder liner is better than the pressure liner, suitable for installation in the coarse grinding warehouse. 4, small corrugated liner crest and pitch are small, suitable for fine grinding and coal mill. 5, end cover liner installed in the grinding head cover or cylinder cover to protect the end cover from wear and tear. 6, ring groove liner in the lining of the T surface for casting a circular groove, after installation to form a circular groove, suitable for multi-warehouse grinding of the first and second positions, dry, wet grinding Machine can be. 7, grading liner, grinding mill for the ideal state should be large particles of material with a large diameter grinding body to impact and crush, that is, in the direction of the mill feed with large diameter grinding body, with the material The direction of the material to the gradual reduction of the grinding body should be sequentially reduced.

Qiming Casting is one of the largest manganese steel, chromium steel, and alloy steel foundry in China. Products include crusher wear parts, Crusher spare parts, mill liners, shredder wear parts, apron feeder pans, and electric rope shovel parts.

grinding equipment, calcination equipments products from china manufacturers - citichl heavy industries co., ltd. - page 1

grinding equipment, calcination equipments products from china manufacturers - citichl heavy industries co., ltd. - page 1

Ball Mill, Jaw Crusher, Mine Hoist manufacturer / supplier in China, offering Rotary Kiln Spare Parts Rotary Kiln Tyre/Ring, Factory Sell Vertical Shaft Impact Crusher for Sand Stone Making/Limestone Crusher, Mining Parts Stainless Forging&Casting Pinion Shaft/Shaft Manufacturer and so on.

use hardox wear plate in your ball mill get your free quote! - hardox wearparts

use hardox wear plate in your ball mill get your free quote! - hardox wearparts

A ball mill consists of a hollow cylindrical shell that rotates about its axis. It is partially filled with balls that can be made in chrome steel, stainless steel, rubber or ceramic. The inner part of the shell is usually lined with an abrasion-resistant material such as manganese steel or rubber. For many years, Hardox steel has been used in inlet chutes and gratings to help extend service life and decrease downtime in ball mills.

qiming machinery | wear parts for mining, quarrying & cement industry

qiming machinery | wear parts for mining, quarrying & cement industry

Qiming Machinery is the leading manganese steel, chromium steel, alloy steel, and heat-resisting steel manufacturer in China. We manufacture replacement wear part castings for impact, abrasion, and high heat applications in mining, crushing, grinding, and shredding, for industrial clients worldwide. No matter which wear parts you are interested in, send us the drawings or sample products, you will get the best products and professional suggestions. Know more+

Qiming Machinery manufactures shredder wear parts, crusher wear parts, mill liners, TIC inserts wear parts, apron feeder pans, and other industries wear parts for ore and aggregate crushers, metal and waste shredders, coal-fired power plants, cement industry, and custom application.

Qiming Machinery manufactures AG mill liner, SAG mill liner, ball mill liner, roll mill liner, and other types of mill liners for all popular brands. Material includes Cr-Mo, manganese, chrome, Ni-hard, and other steel.

Our steel casting foundry services include manganese steel casting, chromium steel casting, alloy steel casting, and carbon steel casting. Casting products of our steel casting foundry span across many industries. On the other hand, customized materials also can be manufactured after checked with our professional engineers.

Qiming Machinery manufactures ASTM A128 standard manganese steel wear parts over 12,000 tons per year, which products include cone crusher liners, jaw crusher liners, mill liner, apron feeder pans, hammer mill hammer, and other wear parts.

Qiming Machinery manufactures ASTM A532M standard chromium steel wear parts over 4,000 tons per year, which products include impact crusher blow bars, impact plates, feed tube, VSI wear parts, mill liners, distributor plate, and other wear parts.

As an alloy steel casting foundry, Qiming Machinery specialized in manufacturing low-alloy steel and high-alloy steel parts. Material includes Cr-Mo alloy steel, 30CrNiMo alloy steel, heat-resistant alloy steel. Products include alloy mill liners, alloy hammer, heat-resistant liners

Qiming Machinery has had cooperation with casting foundries to offer carbon steel (ZG250-700, ZG20SiMn, G20Mn5, ASTM A148, ASTM A488, ASTM A781, ASTM A802) wear parts, which include cone crusher shell, jaw crusher flywheel, pitman, adjustment ring, and other parts.

We have a customer from Australia, who runs MVP450 cone crusher to crush hard stone. However, the original wear parts just can work for around 7 days. This customer wants to prolong this mantle and concave span life. After visiting our foundry, this customer wants us to manufacture TIC insert MVP450 mantle and concave to

Qiming Machinery is a professional cone crusher liner manufacture in China. We had exported more than 12,000 tons of cone crusher liners for our customers. Recently, we get a trail order from Serbia to test our Mn18Cr2 HP300 cone crusher mantle and concave. About the feedback, please check the following communication message: T The messages

We have a Philippines customer who has four crushing lines to crush hard stone. There are 1 set HPT300 crushing lines, 1 set PEW760 crushing line, 1 set HP200 crushing line, and 1 set HP300 crushing line. They had tested many foundries crusher wear parts, however, no products have a long working life. From April

Qiming Machinery is the leading manganese steel, chromium steel, alloy steel, and heat-resisting steel manufacturer in China. We manufacture crusher wear parts, shredder wear parts, mill liners, apron feeder pans, and other wear parts for customers.

mayang crusher spare parts: jaw crusher spare parts

mayang crusher spare parts: jaw crusher spare parts

In 1985, the predecessor of Mayang Company Wuyi Mayang Precision Casting Factory was established, Our company is specialized in producing high-manganese steel, alloy steel, high chromium cast iron, carbon steel, heat-resistant steel and other castings, At first establishing stage the company makes a tremendous investment in including the industrial plants of 120,000 square meters.

wet grid ball mill

wet grid ball mill

Grid ball mill is widely used in smashing all kinds of ores and other materials, ore dressing and national economic departments like building and chemical industries etc. The size of ore shall not exceed 65mm and the best feed size is under 6mm. The effect in this job is better than coarse grinding. Grid ball mill consists of the shell, feeding part, discharging part, main bearing, lubricating system, driving system and other parts. There is wearing a liner inside the shell, and both ends of the shell are provided with a flange. The end cover of the mill is connected with the flange plate. The feeding part consists of the head, trunnion and feeding device. The discharge part includes the grid plate, head, and discharge trunnion.

Wet Grid ball mill is mainly used for mixing and grinding materials in two types: dry grinding and wet grinding .It has advantages of fineness uniformity and power saving. The machine uses different types of liner to meet different customer needs. The grinding fineness of material can be controlled by grinding time. The electro-hydraulic machine is auto-coupled and decompressed to reduce the starting current, and its structure is divided into integral type and independent type.

Compared with similar products,Wet Grid ball mill has the characteristics of low investment, low energy consumption, novel structure, simple operation, stable and reliable performance. It is suitable for mixing and grinding ordinary and special materials. The users can choose the right type, liner and medium type by considering the specific gravity, hardness, yield and other factors. The grinding medium is Wet Grid ball.

1.The ball mill is composed of a horizontal cylinder, a hollow shaft for feeding and discharging, and a grinding head. The main body is a long cylinder made of steel. The cylinder is provided with an abrasive body, and the steel lining plate is fixed to the cylinder body. The grinding body is generally a steel ball and is loaded into the cylinder according to different diameters and a certain proportion, and the grinding body can also be used with a steel section.

2.According to the particle size of the grinding material, the material is loaded into the cylinder by the hollow shaft of the wet grid ball mill feeding end. When the ball mill cylinder rotates, the grinding body acts on the cylinder liner due to the action of inertia and centrifugal force and friction. It is carried away by the cylinder. When it is brought to a certain height, it is thrown off due to its own gravity. The falling abrasive body crushes the material in the cylinder like a projectile.

3.The material is uniformly fed into the first chamber of the mill by the feeding device through the hollow shaft of the feeding material. The chamber has a step liner or a corrugated liner, and various steel balls are loaded therein. The rotation of the cylinder generates centrifugal force to bring the steel ball to a certain extent. The height drops and then hits and grinds the material. After the material reaches the rough grinding in the first bin, it enters the second bin through the single-layer partition plate. The bin is embedded with a flat liner with steel balls inside to further grind the material. The powder is discharged through the discharge raft to complete the grinding operation.

The main function of the steel ball in the ball mill is to impact crush the material and also play a certain grinding effect. Therefore, the purpose of grading steel balls is to meet the requirements of these two aspects. The quality of the crushing effect directly affects the grinding efficiency, and ultimately affects the output of the ball mill. Whether the crushing requirement can be achieved depends on whether the grading of the steel ball is reasonable, mainly including the size of the steel ball, the number of ball diameters, and the ball of various specifications. Proportion and so on.

The ball mill is composed of the main part such as a feeding part, a discharging part, a turning part, a transmission part (a reduction gear, a small transmission gear, a motor, and electric control). The hollow shaft is made of cast steel, the inner lining can be replaced, the rotary large gear is processed by casting hobbing, and the barrel is embedded with wear-resistant lining, which has good wear resistance. The machine runs smoothly and works reliably.

manganese steel, chrome steel , alloy steel foundry | qiming casting

manganese steel, chrome steel , alloy steel foundry | qiming casting

Qiming Casting is a dynamically growing company with many years of experience in production and supply Crusher Wear Parts,Shredder Wear Parts,Mill Liners,Apron Feeder Pans,Electric Rope Shovel Parts, andCrusher Spare Parts. We supply wear parts to the USA, Canada, Europe, Australia, Africa, etc.

Qiming Casting designs and manufactures world-class wear part solutions that last longer than OEM parts. Using the latest technology, we design and cast our products from the best quality alloys available, and use custom heat treatments to ensure the durability of our parts. Our huge product range, customer service excellence, and our ability to deliver on time, every time is the result of 30+ years of operation and industry-based knowledge we know what you need, so we deliver it.

Qiming Casting specializes in manufacturing crusher wear parts, which include jaw crusher wear parts, cone crusher wear parts, hammer mill wear parts, gyratory crusher wear parts, VSI crusher wear parts, impact crusher wear parts.

Qiming Casting supplies all kinds of brands of crusher spare parts, which include jaw crusher spare parts, cone crusher spare parts, gyratory crusher spare parts, VSI crusher spare parts, impact crusher spare parts and other crusher spare parts.

Qiming Casting manufactures ASTM A128 standard manganese steel wear parts for quarrying, mining, and cement wear parts, which products include cone crusher liners, jaw crusher liners, mill liner, apron feeder pans, hammer mill hammer, and others.

Qiming Casting manufactures ASTM A532M standard chromium steel wear parts for quarrying, mining, and cement wear parts, which products include impact crusher blow bars, impact plates, feed tube, VSI wear parts, mill liners, distributor plate, and other wear parts.

Qiming Casting specialized in manufacturing low-alloy steel and high-alloy steel parts. Material includes Cr-Mo alloy steel, 30CrNiMo alloy steel, heat-resistant alloy steel. Products include alloy mill liners, alloy hammer, heat-resistant liners, and other alloy steel liners.

Qiming Casting has a rich experience in cast manganese steel, chromium steel, and alloy steel wear parts for over 30 years. There are more than 12000 tons of wear parts are sent to European, North America, South America, and Australia markets.

Based on rich experience, our engineers also help our customers to design suitable material for different working conditions. On the other hand, Qiming Castings engineers had invented new materials to prolong wear parts span life, such as TIC inserts wear parts, alloy steel crusher liner

Our company has two water glass sand production lines, a V-method casting production lines, an EPC production line, a machine shop; 2 sets 5T electric furnace, 2 sets 3T intermediate frequency electric furnace, 2 sets 1T intermediate frequency electric furnace, 5 sets heat treatment furnace trolley,2000 CBM heat treatment pool, The maximum casting weight:12 tons, Registered capital: Fifteen million dollars, The annual production capacity: 12,000 tons

Although there are only 168 workers in Qiming Casting, however, there are 8 rich experience foundry engineers and 10 quality control personnel. The high percentage of engineers helps us to keep a high-quality standard.

Qiming Casting is one of the largest manganese steel, chromium steel, and alloy steel foundry in China. Products include crusher wear parts, Crusher spare parts, mill liners, shredder wear parts, apron feeder pans, and electric rope shovel parts.

Related Equipments